Section 37 (Controller Area Network (Can))
WARNING: This page is about a different car, the 2020 Mitsubishi Outlander PHEV. However, it is still accessible from the selected car via links, so may be relevant.
- General Information
- Special Tools
- Test Equipment
- Service Precautions
- Precautions On How To Repair The Can Bus Lines
- Explanation About The Scan Tool (M.U.T.-IIISE) Can Bus Diagnostics
- Diagnosis
- Can Bus Diagnostics Table
- Can-Related Connector Position
- Can Bus Diagnostics
- Diagnostic Item 1: Communication with no ECUs is possible (CAN-C)
- Diagnostic Item 2: Diagnose shorts in the power supply to CAN-C
- Diagnostic Item 3: Diagnose shorts in the ground to CAN-C
- Diagnostic Item 4: Diagnose shorts between CAN_H and L lines (CAN-C)
- Diagnostic Item 5: Communication with no ECUs is possible (GW-CAN-C).
- Diagnostic Item 6: Diagnose shorts in the power supply to GW-CAN-C.
- Diagnostic Item 7: Diagnose shorts in the ground to GW-CAN-C.
- Diagnostic Item 8: Diagnose shorts between CAN_H and L lines (GW-CAN-C).
- Diagnostic Item 9: Communication with no ECUs is possible (CAN-C-Mid)
- Diagnostic Item 10: Diagnose shorts in the power supply to CAN-C-Mid
- Diagnostic Item 11: Diagnose shorts in the ground to CAN-C-Mid
- Diagnostic Item 12: Diagnose shorts between CAN_H and L lines (CAN-C-Mid)
- Diagnosis Item 13: Communication with no ECUs is possible (EV-CAN)
- Diagnosis Item 14: Diagnose shorts in the power supply to EV-CAN
- Diagnosis Item 15: Diagnose shorts in the ground to EV-CAN
- Diagnosis Item 16: Diagnose shorts between CAN_H and L lines (EV-CAN)
- Diagnostic Item 17: Diagnose when the scan tool cannot receive the data sent by ETACS-ECU
- Diagnostic Item 18: Diagnose when the scan tool cannot receive the data sent by gateway-ECU.
- Diagnostic Item 19: Diagnose when the scan tool cannot receive the data sent by SRS-ECU
- Diagnostic Item 20: Diagnose when the scan tool cannot receive the data sent by steering wheel sensor
- Diagnostic Item 21: Diagnose when the scan tool cannot receive the data sent by occupant classification-ECU
- Diagnostic Item 22: Diagnose when the scan tool cannot receive the data sent by electric parking brake ECU
- Diagnostic Item 23: Diagnose when the scan tool cannot receive the data sent by FCM/LDW/AHB-ECU.
- Diagnostic Item 24: Diagnose the lines between the joint connectors (CAN3 and CAN1)
- Diagnosis Item 25: Diagnose when the scan tool cannot receive the data sent by PHEV-ECU
- Diagnostic Item 26: Diagnose when the scan tool cannot receive the data sent by EPS-ECU
- Diagnostic Item 27: Diagnose when the scan tool cannot receive the data sent by ASC-ECU
- Diagnostic Item 28: Diagnose the lines between the joint connectors (CAN1 and CAN2).
- Diagnostic Item 29: Diagnose when the scan tool cannot receive the data sent by ACC-ECU.
- Diagnostic Item 30: Diagnose when the scan tool cannot receive the data sent by engine control module (ECM)
- Diagnostic Item 31: Diagnose when the scan tool cannot receive the data sent by BSW-ECU.
- Diagnostic Item 32: Diagnose when the scan tool cannot receive the data sent by OSS-ECU
- Diagnostic Item 33: Diagnose when the scan tool cannot receive the data sent by KOS-ECU
- Diagnostic Item 34: Diagnose when the scan tool cannot receive the data sent by smartphone link display audio
- Diagnostic Item 35: Diagnose when the scan tool cannot receive the data sent by A/C-ECU
- Diagnostic Item 36: Diagnose when the scan tool cannot receive the data sent by power liftgate control unit
- Diagnostic Item 37 Diagnose when the scan tool cannot receive the data sent by EV remote-ECU.
- Diagnostic Item 38: Diagnose when the scan tool cannot receive the data sent by camera-ECU.
- Diagnostic Item 39: Diagnose when the scan tool cannot receive the data sent by combination meter
- Diagnosis Item 40: Diagnose when the scan tool cannot receive the data sent by power drive unit
- Diagnosis Item 41: Diagnose when the scan tool cannot receive the data sent by A/C compressor
- Diagnosis Item 42: Diagnose the lines between the joint connectors (CAN2 and CAN1)
- Diagnosis Item 43: Diagnose when the scan tool cannot receive the data sent by electrical parking driver unit
- Diagnosis Item 44: Diagnose the lines between the joint connectors (CAN1 and CAN9)
- Diagnosis Item 45: Diagnose when the scan tool cannot receive the data sent by electric heater-ECU
- Diagnosis Item 46: Diagnose the lines between the joint connectors (CAN9 and CAN6)
- Diagnosis Item 47: Diagnose when the scan tool cannot receive the data sent by REMCU
- Diagnosis Item 48: Diagnose when the scan tool cannot receive the data sent by on board charger/DC-DC converter
- Can Communication-Related DTC (U-Code) Table
- Diagnosis
- Standard Flow Of Diagnostic Troubleshooting
- Diagnosis Function
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- Data List Reference Table
- Trouble Symptom Chart
- Symptom Procedures
- Trouble Symptom Chart For Input Signal
- Input Signal Procedures
- Terminal Voltage Reference Chart
- Gateway-Ecu