Common Specs & Procedures
ECLIPSE CROSS COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SERVICE SPECIFICATIONS | ||
| Torque | Torque specification are found in article text and article figures. | ||
| Axle Nut/Hub Nut | |||
| Front | 250 ± 25 (184 ± 18 ft-lb) | ||
| Rear (FWD) | 95 ± 14 N.m (70 ± 10 ft-lb) | ||
| Rear (AWD) | 250 ± 25 (184 ± 18 ft-lb) | ||
| Battery | GENERAL INFORMATION , BATTERY CHARGING | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING | ||
| Disc Brakes | |||
| Service Specifications | SERVICE SPECIFICATIONS | ||
| Torque | Torque specification are found in article text and article figures. | ||
| Charging | |||
| Generator | GENERATOR SPECIFICATIONS , SERVICE SPECIFICATIONS | ||
| Torque | Torque specification are found in article text and article figures. | ||
| Drive Belts | |||
| Adjustment | DRIVE BELT TENSION CHECK AND ADJUSTMENT | ||
| Belt Routing | DRIVE BELT INSTALLATION | ||
| Engine Cooling | |||
| General Service Specifications | SERVICE SPECIFICATIONS , COOLANT | ||
| Radiator Cap Pressure | Standard value: 93 - 123 kPa (14-18 psi), Minimum limit: 83 kPa (12 psi) | ||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | Standard value (at engine speed of 250 RPM): 1, 330 kPa (193 psi). Minimum limit: 990 kPa (144 psi). Difference between cylinders: Limit: 98 kPa (14 psi) | ||
| Oil Pressure | Oil pressure at curb idle: 29 kPa (4.2 psi) or more; At 3, 500 RPM: 294 - 686 kPa (42.7 - 99.4 psi) | ||
| Overhaul | SERVICE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 100 ± 5 N.m (74 ± 3 ft-lb) | ||
| Fuel System | |||
| Pressure Specification | 450 kPa (65.26 psi) at curb idle | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE TEST | ||
| Fuel Filter Location | Fuel filter is part of fuel pump module. | ||
| Fuel Filter R & I | FUEL PUMP (MODULE) REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil on plug | ||
| Ignition Wires (Routing) | Coil on plug | ||
| Spark Plug | |||
| Type | NGK; SILKR7H8 | ||
| Gap | Standard Value: 0.028-0.031 in. (0.7-0.8 mm). Limit: 0.04in. (1.0mm) | ||
| Torque | 18 ± 2 N.m (13 ± 1 ft-lb). | ||
| Starting | |||
| Starter | STARTER MOTOR SPECIFICATIONS ,SERVICE SPECIFICATIONS | ||
| Torque | Torque specification are found in article text and article figures. | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Front | SERVICE SPECIFICATIONS | ||
| Rear | SERVICE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 98 ± 10 N.m (72 ± 7 ft. lbs.) | ||