Work Procedure

WARNING: This page is about a different car, the 2024 Mitsubishi Outlander. However, it is still accessible from the selected car via links, so may be relevant.

CHECK DTC
Check DTC.

Is any DTC detected?

YES >>

Repair malfunction(s) and erase DTC. Refer to DTC INDEX .

NO >>

GO TO 2.
CHECK SRT STATUS
Without M.U.T.-III SE

Perform "SRT status" mode with Refer to ON BOARD DIAGNOSIS FUNCTION .

ith GST

Select Service $01 with GST.

Is SRT code(s) set?

YES >>

GO TO 10.

NO >>

Without M.U.T-III SE:

GO TO 3.
PERFORM ROAD TEST
- Check the "Performance Priority" in the "SRT ITEM" table. Refer to DESCRIPTION .
- Perform the most efficient SRT set driving pattern to set the SRT properly. Refer to SRT SET DRIVING PATTERN .
In order to set all SRTs, the SRT set driving pattern must be performed at least once.

>>

GO TO 4.
PATTERN 1
1. Check the vehicle condition;
  - Engine coolant temperature is -10 to 35°C (14 to 95°F).
  - Fuel tank temperature is more than 0°C (32°F).
2. Start the engine.
3. Keep engine idling until the engine coolant temperature is greater than 70°C (158°F)
NOTE:
ECM terminal voltage is follows;
- Engine coolant temperature
  - -10 to 35°C (14 to 95°F): 3.0 - 4.3 V
  - 70°(158°F): Less than 4.1 V
- Fuel tank temperature: Less than 1.4 V
Refer to VALUES ON THE DIAGNOSIS TOOL .

>>

GO TO 5.
PATTERN 2
1. Drive the vehicle. And depress the accelerator pedal until vehicle speed is 90 km/h (56 MPH), then release the accelerator pedal and keep it released for more than 10 seconds.
2. Depress the accelerator pedal until vehicle speed is 90 km/h (56 MPH) again
NOTE:
- Checking the vehicle speed with GST is advised.
- When steady-state driving is performed again even after it is interrupted, each diagnosis can be conducted. In this case, the time required for diagnosis may be extended.
>>

GO TO 6.

PATTERN 3

Operate vehicle following the driving pattern shown in the figure.

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

Release the accelerator pedal during deceleration of vehicle speed from 90 km/h (56 MPH) to 0 km/h (0 MPH).

GO TO 7.

PATTERN 4

Operate vehicle following the driving pattern shown in the figure.

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

Drive the vehicle in a proper gear at 60 km/h (38 MPH) and maintain the speed.
Release the accelerator pedal fully at least 5 seconds.
Repeat the above two steps at least 5 times.

GO TO 8.

PATTERN 5
- The accelerator pedal must be held very steady during steady-state driving.
- If the accelerator pedal is moved, the test must be conducted again.
>>

GO TO 9.
CHECK SRT STATUS
Without M.U.T.-III SE

Perform "SRT status" mode with Refer to ON BOARD DIAGNOSIS FUNCTION .

With GST

Select Service $01 with GST.

Is SRT(s) set?

YES >>

GO TO 10.

NO >>

Call TECH LINE or take appropriate action.
CHECK PERMANENT DTC
NOTE: Permanent DTC cannot be checked with a tool other than M.U.T.-III SE or GST.

With M.U.T.-III SE

Select "SRT STATUS" of "ENGINE" with M.U.T.-III SE.

With GST

Select Service $0A with GST.

Is permanent DTC(s) detected?

YES >>

Refer to DESCRIPTION .

NO >>

END