LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mitsubishi >> 2023 >> Outlander ES, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 85 (ADAS Control Unit) >> Ecu Diagnosis Information >> ADAS Control Unit 2 >> Reference Value >> Values On The Diagnosis Tool
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Values On The Diagnosis Tool

WARNING: This page is about a different car, the 2024 Mitsubishi Outlander. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: The following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to M.U.T.-III SE display items.
Monitor item Condition Value/Status
Current malfunction Ignition switch ON Displays DTC detected as the current malfunction
PWR SUP MONI Ignition switch ON 10 - 16 V
Ignition switch Ignition switch ON ON
MAIN SW Ignition switch ON When MI-PILOT Assist MAIN switch is pressed ON
When MI-PILOT Assist MAIN switch is not pressed OFF
CANCEL SW Ignition switch ON When CANCEL switch is pressed ON
When CANCEL switch is not pressed OFF
SET/COAST SW Ignition switch ON When SET- switch is pressed ON
When SET- switch is not pressed OFF
RESUME/ACC SW Ignition switch ON When RES+ switch is pressed ON
When RES+ switch is not pressed OFF
DISTANCE SW Ignition switch ON When DISTANCE switch is pressed ON
When DISTANCE switch is not pressed OFF
Switch1 Ignition switch ON When Lane Keep Assist [LKA] switch is pressed ON
When Lane Keep Assist [LKA] switch is not pressed OFF
Switch2
NOTE: The item is displayed, but it is not monitored
-
BRAKE SW Ignition switch ON When brake pedal is not depressed ON
When brake pedal is depressed OFF
IDLE SW Engine running Idling ON
Except idling (depress accelerator pedal) OFF
STOP LIGHT SW
NOTE: The item is displayed, but it is not monitored
-
DRIVE MODE STATS
NOTE: The item is displayed, but it is not monitored
-
G (vertical)
NOTE: The item is displayed, but it is not monitored
-
G (lateral)
NOTE: The item is displayed, but it is not monitored
-
Vehicle speed While driving Almost the same speed as speedometer indication
SET VHCL SPD When vehicle speed is set Displays the set vehicle speed
EPS ST angle command value
NOTE: The item is displayed, but it is not monitored
-
EPS status
NOTE: The item is displayed, but it is not monitored
-
EPS control request
NOTE: The item is displayed, but it is not monitored
-
Vibration motor open status Ignition switch ON Open circuit in steering vibration motor circuit is detected On
Open circuit in steering vibration motor circuit is not detected Off
ENGINE RPM Engine running Almost the same speed as the tachometer indication
THRTL OPENING Engine running 0 - 100 %
GEAR
NOTE: The item is displayed, but it is not monitored
-
CLUTCH SW SIG
NOTE: The item is displayed, but it is not monitored
-
Neutral switch
NOTE: The item is displayed, but it is not monitored
-
Parking brake holding request
NOTE: The item is displayed, but it is not monitored
-
Parking brake release request
NOTE: The item is displayed, but it is not monitored
-
Wiper signal Ignition switch ON When wiper LO is operating Low
When wiper HI is operating High
Turn signal Ignition switch ON Turn signal is OFF OFF
Turn signal LH is operating LH
Turn signal RH is operating RH
SET DISTANCE MI-PILOT Assist system ON and press the DISTANCE switch to change the vehicle-to-vehicle distance setting When set to "long" Long
When set to "middle" Mid
When set to "short" Short
Own vehicle mark
NOTE: The item is displayed, but it is not monitored
-
VHCL AHEAD Drive the vehicle and activate the vehicle-to-vehicle distance control mode When a vehicle ahead is detected (vehicle ahead detection indicator ON) ON
When a vehicle ahead is not detected (vehicle ahead detection indicator OFF) OFF
Vhcl ahead recognition Drive the vehicle and activate the vehicle-to-vehicle distance control mode When a vehicle ahead is detected OK
When a vehicle ahead is not detected NG
CRUISE LIGHT
NOTE: The item is displayed, but it is not monitored
-
CRUISE OPE Drive the vehicle and activate the vehicle-to-vehicle distance control mode When MI-PILOT Assist ASSIST system is controlling ON
When MI-PILOT Assist ASSIST system is not controlling OFF
Pro Pilot ON/OFF request
NOTE: The item is displayed, but it is not monitored
-
FEB SELECT Ignition switch ON When AEB is ON ON
When AEB is OFF OFF
LDW SELECT Ignition switch ON When LDW is ON ON
When LDW is OFF OFF
LDP SELECT Ignition switch ON When LDP is ON ON
When LDP is OFF OFF
Steering assist function select Ignition switch ON When Steering assist function is ON ON
When Steering assist function is OFF OFF
FEB SW
NOTE: The item is displayed, but it is not monitored
-
ACC warning output Ignition switch ON MI-PILOT Assist malfunction message: ON ON
MI-PILOT Assist malfunction message: OFF OFF
Speed control mode Ignition switch ON When the vehicle-to-vehicle distance control mode is operating ACC
When the conventional (fixed speed) cruise control mode is operating ASCD
When the cruise control mode is OFF OFF
Set display light Ignition switch ON When the vehicle-to-vehicle distance control mode system display is ON ACC
When the conventional (fixed speed) cruise control mode system display is ON ASCD
When the cruise control mode system display is OFF OFF
LDP system
NOTE: The item is displayed, but it is not monitored
-
LDP control Ignition switch ON LDP system is malfunctioning ABNML
LDP system is normal NRML
LDW system Ignition switch ON When LDW is ON ON
When LDW is OFF OFF
Steering torque (measured)
NOTE: The item is displayed, but it is not monitored
-
Steering torque rgstrtn stats
NOTE: The item is displayed, but it is not monitored
-
Steering torque error cause
NOTE: The item is displayed, but it is not monitored
-