Common Specs & Procedures
OUTLANDER PHEV COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Torque | Torque specification are found in article text and article figures. | ||
| Axle Nut/Hub Nut | |||
| Front | 240 - 270 N.m (177.1 - 199.1 ft-lb) | ||
| Rear | 113 N.m (83 ft-lb) | ||
| 12V Battery | 12V BATTERY | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING BRAKE SYSTEM | ||
| Disc Brakes | |||
| Service Specifications | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Torque | Torque specification are found in article text and article figures. | ||
| Battery Management Unit | SERVICE SPECIFICATIONS | ||
| Torque | Torque specification are found in article text and article figures. | ||
| Drive Belts | |||
| Adjustment | WATER PUMP DRIVE BELT INSPECTION | ||
| Belt Routing | WATER PUMP DRIVE BELT INSTALLATION | ||
| Engine Cooling | |||
| General Service Specifications | SERVICE SPECIFICATIONS | ||
| Radiator Cap Pressure | Standard value: 93 - 123 kPa (14-18 psi), Minimum limit: 83 kPa (12 psi) | ||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | Standard value (at engine speed of 300 RPM): 1, 150 kPa (167 psi). Minimum limit: 850 kPa (123 psi). Difference between cylinders: Limit: 98 kPa (14 psi) | ||
| Oil Pressure | Oil pressure at curb idle: 29 kPa (4.2 psi) or more; At 3, 500 RPM: 294-686 kPa (43-100 psi) | ||
| Overhaul | SERVICE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | First Pass: 40 N.m (30 ft-lb); Second Pass: 130 N.m (95 ft-lb) | ||
| Fuel System | |||
| Pressure Specification | 324 kPa (47 psi) at curb idle | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE TEST | ||
| Fuel Filter Location | Fuel filter is part of fuel pump module. | ||
| Fuel Filter R & I | FUEL TANK PUMP AND GAUGE ASSEMBLY REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil on plug | ||
| Ignition Wires (Routing) | Coil on plug | ||
| Spark Plug | |||
| Type | NGK; SILMAR6G8GS | ||
| Gap | Standard Value: 0.027-0.031 in. (.7-.8 mm). Limit: 0.04 in. (1.0 mm) | ||
| Torque | 13 +/- 2 N.m (115 +/- 17 in-lb). | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Front | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Rear | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 83 ft. lb (113 N.m) | ||