Common Specs & Procedures
MIRAGE COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | GENERAL DESCRIPTION and SERVICE SPECIFICATIONS | ||
| Torque | Torque specification are found in article text and article figures. | ||
| Axle Nut/Hub Nut | |||
| Front | 270 ± 27 (199 ± 20 ft-lb) | ||
| Rear | 175 ± 25 N.m (129 ± 18 ft-lb) | ||
| Battery | GENERAL DESCRIPTION , BATTERY CHARGING | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING | ||
| Disc Brakes | |||
| Service Specifications | SERVICE SPECIFICATIONS | ||
| Torque | Torque specification are found in article text and article figures. | ||
| Charging | |||
| Generator | GENERATOR SPECIFICATIONS or SERVICE SPECIFICATIONS | ||
| Torque | Torque specification are found in article text and article figures. | ||
| Drive Belts | |||
| Adjustment | DRIVE BELT TENSION CHECK AND ADJUSTMENT | ||
| Belt Routing | DRIVE BELT INSTALLATION | ||
| Engine Cooling | |||
| General Service Specifications | SERVICE SPECIFICATIONS | ||
| Radiator Cap Pressure | Standard value: 93 - 123 kPa (13.5-17.8 psi), Minimum limit: 83 kPa (12 psi) | ||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | Standard value (at engine speed of 250 RPM): 1, 410 kPa (205 psi). Minimum limit: 950 kPa (138 psi). Difference between cylinders: Limit: 98 kPa (14 psi) | ||
| Oil Pressure | Oil pressure at curb idle: 29 kPa (4.2 psi) or more; At 3, 500 RPM: 294-686 kPa (42.7-99.4 psi) | ||
| Overhaul | SERVICE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 100 ± 5 N.m (74 ± 3 ft-lb) | ||
| Fuel System | |||
| Pressure Specification | 324 kPa (47 psi) at curb idle | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE TEST | ||
| Fuel Filter Location | Fuel filter is part of fuel pump module. | ||
| Fuel Filter R & I | FUEL PUMP MODULE REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION |
||
| Ignition Wires (Resistance) | Coil on plug | ||
| Ignition Wires (Routing) | Coil on plug | ||
| Spark Plug | |||
| Type | NGK; LZFR5DI-11 | ||
| Gap | Standard Value: 0.040-0.043 in. (1.0-1.1 mm). Limit: 0.06 in. (1.5 mm) | ||
| Torque | 25 +/- 5 N.m (18 +/- 3 ft-lb). | ||
| Starting | |||
| Starter | STARTER MOTOR SPECIFICATIONS , SERVICE SPECIFICATION | ||
| Torque | Torque specification are found in article text and article figures. | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Front | SERVICE SPECIFICATIONS | ||
| Rear | SERVICE SPECIFICATIONS | ||
| Torque | |||
| Front | FASTENER TIGHTENING SPECIFICATIONS | ||
| Rear | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 72 ± 7 ft. lbs. (98 ± 10 N.m) | ||