Common Specs & Procedures
OUTLANDER COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | See SERVICE DATA AND SPECIFICATIONS (SDS) . | ||
| Torque | Torque specifications are included in article text and figures. | ||
| Axle Nut/Hub Nut | |||
| Front | 240.0- 270.0 N.m (24.5 - 27.6 kg-m, 177.1- 199.1 ft-lb) | ||
| Rear - AWD | 125 N.m (13 kg-m, 92 ft. lb.) | ||
| Battery | See BATTERY | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING BRAKE SYSTEM | ||
| Disc Brakes | |||
| Service Specifications | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Torque | Torque specifications are included in article text and figures. | ||
| Charging | |||
| Generator | See GENERATOR | ||
| Torque | Torque specifications are included in article text and figures. | ||
| Drive Belts | |||
| Adjustment | |||
| 2.5L | ADJUSTMENT | ||
| Drive Belt Routing | |||
| 2.5L | Refer to Drive Belt And Pulley System Diagram figure under REMOVAL AND INSTALLATION | ||
| Engine Cooling | |||
| General Service Specifications | See SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Radiator Cap Pressure | Standard value: 130-150 kPa (18.85-21.75 psi); Minimum limit: 110 kPa (15.95 psi) | ||
| Thermostat R & I | |||
| 2.5L | REMOVAL AND INSTALLATION | ||
| Water Pump R & I | |||
| 2.5L | REMOVAL AND INSTALLATION | ||
| Engine Mechanical | |||
| 2.5L | |||
| Compression | Standard value (at 250 RPM): 1, 10 kPa (204.5 psi): Minimum limit 1, 20 kPa (176.9 psi); differential limit between cylinders: Limit: 100 kPa (14.5 psi) | ||
| Oil Pressure | Engine oil pressure: at 600 RPM: More than 70 kPa (10.15 psi); at 2, 000 RPM: More than 185 kPa (26.83 psi); at 4, 000 RPM: 670 kPa (97.15 psi) | ||
| Specifications | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Drive Plate Torque | |||
| 2.5L | 107.8 N.m (80 ft. lb.) | ||
| Fuel System | |||
| Pressure Specification | 500 kPa (72.5 psi) at idle | ||
| Fuel Pressure Test Procedure | |||
| 2.5L | FUEL PRESSURE | ||
| Fuel Filter Location | Fuel filter is part of fuel pump module, which is located in fuel tank. | ||
| Fuel Filter R & I | FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY | ||
| Ignition | |||
| Firing Order & Cylinder Identification | See FIRING ORDER & CYLINDER IDENTIFICATION article. | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| 2.5L | |||
| Type | DENSO DXE22H11C | ||
| Gap | Nominal: 1.0-1.1 mm (0.039-0.043 in.) | ||
| Torque | 19.6 N.m (14 ft. lb.) | ||
| Starting | |||
| Starter | See SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Torque | Torque specifications are included in article figures. | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Front | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Rear | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Torque | Torque specifications are included in article text and figures. | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 113 N.m (83 ft. lb.) | ||