Transmission Specifications
TRANSAXLE SPECIFICATIONS
| Application | In. (mm) | |||
|---|---|---|---|---|
| Differential Assembly | ||||
| Side Gear-To-Differential Case | ||||
| Specified Clearance | .004-.008 (0.10-0.20) | |||
| Differential End Play | 0-.006 (0-.15) | |||
| Differential Side Bearing Preload | .002-.004 (.04-.010) | |||
| Forward & Overrun Clutches | ||||
| Dish Plate Thickness | ||||
| Forward Clutch | .098 (2.50) | |||
| Overrun Clutch | .085 (2.15) | |||
| Drive Plate Thickness | ||||
| Forward Clutch | ||||
| Specified Clearance | .071 (1.80) | |||
| Allowable Limit | .063 (1.60) | |||
| Overrun Clutch | ||||
| Specified Clearance | .063 (1.60) | |||
| Allowable Limit | .055 (1.40) | |||
| Retaining Plate-To-Snap Ring | ||||
| Forward Clutch | ||||
| Specified Clearance | .018-.0335 (.45-.85) | |||
| Allowable Limit | .073 (1.85) | |||
| Overrun Clutch | ||||
| Specified Clearance | .039-.055 (1.00-1.40) | |||
| Allowable Limit | .079 (2.00) | |||
| High Clutch | ||||
| Drive Plate Thickness | .063 (1.60) | |||
| Allowable Limit | .071 (1.80) | |||
| Retaining Plate-To-Snap Ring | ||||
| Specified Clearance | .055-.071 (1.40-1.80) | |||
| Allowable Limit | .102 (2.60) | |||
| Input Shaft Seal Ring-To-Ring Groove | ||||
| Specified Clearance | .003-.009 (.08-.23) | |||
| Allowable Limit | .009 (.23) | |||
| Low-Reverse Brake | ||||
| Drive Plate Thickness | .079 (2.00) | |||
| Allowable Thickness Limit | .071 (1.80) | |||
| Specified Clearance | .055-.071 (1.40-1.80) | |||
| Allowable Clearance Limit | .110 (2.80) | |||
| Oil Pump Seal Ring-To-Ring Groove | ||||
| Specified Clearance | .004-.010 (.10-.25) | |||
| Allowable Limit | .010 (.25) | |||
| Oil Pump Side Clearance | .0008-.0016 (.020-.040) | |||
| Output Shaft End Play | 0-.02 (0-.5) | |||
| Output Shaft Seal Ring-To-Ring Groove | ||||
| Specified Clearance | .004-.010 (.10-.25) | |||
| Allowable Limit | .010 (.25) | |||
| Pinion Washer-To-Planetary Gear | ||||
| Specified Clearance | .006-.028 (.15-.70) | |||
| Allowable Limit | .031 (.80) | |||
| Reverse Clutch | ||||
| Dish Plate Thickness | .110 (2.80) | |||
| Drive Plate Thickness | .079 (2.00) | |||
| Allowable Limit | .071 (1.80) | |||
| Retaining Plate-To-Snap Ring | ||||
| Specified Clearance | .020-.031 (.50-.80) | |||
| Allowable Limit | .047 (1.20) | |||
| Reduction Gear Bearing Preload | .002 (.05) | |||
| Reverse Clutch End Play | .026-.039 (.65-1.00) | |||
| Total End Play | .010-.022 (.25-.55) | |||