LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2003 >> Sentra SE-R, Automatic >> Repair and Diagnosis >> External Pages >> Different car >> Section 2111 (Lighting System) >> Cornering Lamp >> Cornering Lamp Does Not Operate
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Cornering Lamp Does Not Operate

WARNING: This page is about a different car, the 2008 Nissan Maxima. However, it is still accessible from the selected car via links, so may be relevant.
  1. ACTIVE TEST 

    With CONSULT-III

    1. Select "IPDM E/R" on CONSULT-III, and select "ACTIVE TEST" on "SELECT DIAG MODE" screen.
    2. Select "CORNERING LAMP" on "SELECT TEST ITEM" screen.
    3. Select "RH", then "LH" on "ACTIVE TEST" screen.
    4. Make sure cornering lamp RH and cornering lamp LH operate.

    Without CONSULT-III

    GO TO  3.

    OK or NG 

    OK: GO TO 2.

    NG: GO TO  3.

  2. CHECK COMBINATION SWITCH INPUT SIGNAL 

    Select "IPDM E/R" on CONSULT-III, and select "DATA MONITOR" on "SELECT DIAG MODE" screen. Make sure "CRNRNG LMP REQ" turns ON-OFF linked with operation of lighting switch.

    When lighting switch is in TURN RH position: CRNRNG LMP REQ ON 

    When lighting switch is in TURN LH position: CRNRNG LMP REQ ON 

    OK or NG 

    OK: Replace IPDM E/R. Refer to "REMOVAL AND INSTALLATION OF IPDM E/R ".

    NG: Replace BCM. Refer to "BCM ".

  3. CHECK BULB 

    Check bulb standard of each cornering lamp is correct. Refer to "EXTERIOR LAMP ".

    OK or NG 

    OK: GO TO 4.

    NG: Replace cornering lamp bulb.

  4. CHECK CORNERING LAMPS CIRCUIT 
    1. Turn ignition switch OFF.
    2. Disconnect IPDM E/R connectors and front combination lamp LH and RH connectors.
    3. Check continuity between IPDM E/R connector E122 (A) terminal 23 and front combination lamp RH connector E107 (B) terminal 11.

      11 - 23: Continuity should exist. 

    4. Check continuity between IPDM E/R connector E124 (A) terminal 34 and front combination lamp LH connector E11 (B) terminal 11.

      11 - 34: Continuity should exist. 

    Fig 1: Checking Continuity Between IPDM E/R Connector E124 Terminal 34 And Front Combination Lamp LH Connector E11 Terminal 11
    G04917894Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: GO TO 5.

    NG: Repair harness or connector.

  5. CHECK GROUND 
    1. Check continuity between front combination lamp LH harness connector E11 terminal 10 and ground.

      10 - Ground: Continuity should exist. 

    2. Check continuity between front combination lamp RH harness connector E107 terminal 10 and ground.

      10 - Ground: Continuity should exist. 

    Fig 2: Checking Continuity Between Front Combination Lamp RH Harness Connector E107 Terminal 10 And Ground
    G04917895Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: GO TO 6.

    NG: Repair harness or connector.

  6. CHECK CORNERING LAMPS SHORT CIRCUIT 
    1. Check continuity (short circuit) between front combination lamp LH harness connector E11 terminal 11 and ground.

      11 - Ground: Continuity should not exist. 

    2. Check continuity (short circuit) between front combination lamp RH harness connector E107 terminal 11 and ground.

      11 - Ground: Continuity should not exist. 

    Fig 3: Checking Continuity (Short Circuit) Between Front Combination Lamp Rh Harness Connector E107 Terminal 11 And Ground
    G04917896Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: Replace IPDM E/R. Refer to "REMOVAL AND INSTALLATION OF IPDM E/R ".

    NG: Repair harness or connector.

scientia non olet · About LEMON Manuals