Mirror Sensor LH Circuit Check

WARNING: This page is about a different car, the 2007 Nissan Quest. However, it is still accessible from the selected car via links, so may be relevant.

CHECK DOOR MIRROR FUNCTION
Check the following items.

Operation malfunction in memory control

NOTE: If a door mirror face position is set to an implausible angle, the set position may not be reproduced.

OK or NG

OK: GO TO 2.

NG: Repair the malfunctioning parts, and check the symptom again.

CHECK MIRROR SENSOR INSPECTION

With CONSULT-II

Check that "ON" is displayed on "MIR/SEN LH R-L, MIR/SEN LH U-D" in the DATA MONITOR.

DATA MONITOR REFERENCE

Monitor item [OPERATION or UNIT]		Contents
MIR/SEN LH R-L	"V"	Voltage output from door mirror LH sensor (LH/RH) is displayed.
MIR/SEN LH U-D	"V"	Voltage output from door mirror LH sensor (UP/DOWN) is displayed.

Fig 1: CONSULT II Display - DATA MONITOR

Courtesy of NISSAN MOTOR CO., U.S.A.

Without CONSULT-II

Turn ignition switch to ACC.

Check voltage between door mirror LH connector and ground.

TERMINALS VOLTAGE CHART

Connector	Terminals		Condition	Voltage (V) (Approx.)
Connector	(+)	(-)	Condition	Voltage (V) (Approx.)
D4	7	Ground	When motor is operated LEFT or RIGHT	Changes between 3.5 (close to right edge) - 0.5 (close to left edge)
D4	6	Ground	When motor is operated UP or DOWN	Changes between 3.5 (close to peak) - 0.5 (close to valley)

OK or NG

OK: Mirror sensor LH is OK.

NG: GO TO 3.

Fig 2: Checking Voltage Between Door Mirror LH Connector Terminals 6, 7 And Ground

Courtesy of NISSAN MOTOR CO., U.S.A.

CHECK HARNESS CONTINUITY 1
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and door mirror LH.
3. Check continuity between automatic drive positioner control unit connector M42 terminals 33, 41 and door mirror LH connector D2 terminals 5, 8.
  33 - 5 : Continuity should exist.
  
  41 - 8 : Continuity should exist.
4. Check continuity between automatic drive positioner control unit connector M42 terminals 33, 41 and ground.
  33 - Ground : Continuity should not exist.
  
  41 - Ground : Continuity should not exist.
  
  Fig 3: Checking Continuity Between Automatic Drive Positioner Control Unit Connector M42 Terminals 33, 41 And Ground, And Between Connector M42 Terminals 33, 41 And Door Mirror LH Connector D2 Terminals 5, 8
  Courtesy of NISSAN MOTOR CO., U.S.A.
OK or NG

OK: GO TO 4.

NG: Repair or replace harness.
CHECK HARNESS CONTINUITY 2
1. Check continuity between automatic drive positioner control unit connector M41 terminals 6, 22 and door mirror LH connector D4 terminals 6, 7.
  6 - 6 : Continuity should exist.
  
  22 - 7 : Continuity should exist.
2. Check continuity between automatic drive positioner control unit connector M41 terminals 6, 22 and ground.
  6 - Ground : Continuity should not exist.
  
  22 - Ground : Continuity should not exist.
OK or NG

OK: Replace door mirror LH. Refer to "DOOR MIRROR ASSEMBLY ".

NG: Repair or replace harness.

Fig 4: Checking Continuity Between Automatic Drive Positioner Control Unit Connector M41 Terminals 6, 22 And Ground, And Between Connector M41 Terminals 6, 22 And Door Mirror LH Connector D4 Terminals 6, 7
Courtesy of NISSAN MOTOR CO., U.S.A.