Terminals and Reference Values for Automatic Drive Positioner Control Unit
WARNING: This page is about a different car, the 2006 Nissan Titan. However, it is still accessible from the selected car via links, so may be relevant.
TERMINALS AND REFERENCE VALUES FOR BCM
| TERMINAL | WIRE COLOR | ITEM | CONDITION | VOLTAGE (V) (Approx.) |
|---|---|---|---|---|
| 2 | LG | Changeover switch RH signal | Changeover switch in RH position | 0 |
| Other than above | 5 | |||
| 3 | Y/B | Mirror switch UP signal | Mirror switch in UP position | 0 |
| Other than above | 5 | |||
| 4 | V/W | Mirror switch LEFT signal | Mirror switch in LEFT position | 0 |
| Other than above | 5 | |||
| 5 | R/B | Mirror sensor (RH vertical) signal | Mirror motor RH is operated UP or DOWN | Changes between 3.4 (close to peak) 0.6 (close to valley) |
| 6 | L/Y | Mirror sensor (LH vertical) signal | Mirror motor LH is operated UP or DOWN | Changes between 3.4 (close to peak) 0.6 (close to valley) |
| 8 | BR/Y | Pedal sensor input signal | Pedal position front end | 0.5 |
| Pedal position rear end | 4.5 | |||
| 9 | LG/B | Seat memory switch 1 signal | Memory switch 1 ON | 0 |
| Memory switch 1 OFF | 5 | |||
| 10 | L | UART LINE (TX) | Pedal adjusting switch ON (FORWARD or BACKWARD operation) | |
| 12 | P | Seat memory switch indictor 1 signal | Memory switch 1 ON | 0 |
| Memory switch 1 OFF | Battery voltage | |||
| 13 | Y/G | Seat memory switch indictor 2 signal | Memory switch 2 ON | 0 |
| Memory switch 2 OFF | Battery voltage | |||
| 14 | GR/R | Mirror motor RH UP signal | Mirror motor RH is operated UP | 1.5 - Battery voltage |
| Other than above | 0 | |||
| 15 | V/R | Mirror motor RH LEFT signal | Mirror motor RH is operated LEFT | 1.5 - Battery voltage |
| Other than above | 0 | |||
| 16 | O | Mirror motor LH DOWN signal | Mirror motor LH is operated DOWN | 1.5 - Battery voltage |
| Other than above | 0 | |||
| Mirror motor LH RIGHT signal | Mirror motor LH is operated RIGHT | 1.5 - Battery voltage | ||
| Other than above | 0 | |||
| 18 | BR/W | Changeover switch LH signal | Changeover switch in LH position | 0 |
| Other than above | 5 | |||
| 19 | SB | Mirror switch DOWN signal | Mirror switch in DOWN position | 0 |
| Other than above | 5 | |||
| 20 | GR | Mirror switch RIGHT signal | Mirror switch in RIGHT position | 0 |
| Other than above | 5 | |||
| 21 | L/W | Mirror sensor (RH horizontal) signal | Mirror motor RH is operated LEFT or RIGHT | Changes between 3.4 (close to left edge) 0.6 (close to right edge) |
| 22 | G | Mirror sensor (LH horizontal) signal | Mirror motor LH is operated LEFT or RIGHT | Changes between 3.4 (close to left edge) 0.6 (close to right edge) |
| 24 | G/O | Seat memory set switch signal | Set switch 1 ON | 0 |
| Set switch 1 OFF | 5 | |||
| 25 | P/L | Seat memory switch 2 signal | Memory switch 2 ON | 0 |
| Memory switch 2 OFF | 5 | |||
| 26 | W | UART LINE (RX) | Pedal adjusting switch ON (FORWARD or BACKWARD operation) | |
| 30 | Y | Mirror motor RH DOWN signal | Mirror motor RH is operated DOWN | 1.5 - Battery voltage |
| Other than above | 0 | |||
| Mirror motor RH RIGHT signal | Mirror motor RH is operated RIGHT | 1.5 - Battery voltage | ||
| Other than above | 0 | |||
| 31 | R | Mirror motor LH UP signal | Mirror motor LH is operated UP | 1.5 - Battery voltage |
| Other than above | 0 | |||
| 32 | BR | Mirror motor LH LEFT signal | Mirror motor LH is operated LEFT | 1.5 - Battery voltage |
| Other than above | 0 | |||
| 33 | W/L | Sensor power supply | - | 0 |
| 34 | Y/R | Battery power supply | - | Battery voltage |
| 37 | G | Pedal adjusting motor FORWARD signal | Pedal adjusting motor FORWARD operation (Motor operated) | Battery voltage |
| Other than above | 0 | |||
| 39 | L/B | Battery power supply | - | Battery voltage |
| 40 | B/W | Ground | - | 0 |
| 41 | W/G | Sensor ground | - | 0 |
| 45 | R | Pedal adjusting motor BACKWARD signal | Pedal adjusting motor BACKWARD operation (Motor operated) | Battery voltage |
| Other than above | 0 | |||
| 48 | B | Ground | - | 0 |