LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2004 >> Sentra SE-R >> Repair and Diagnosis >> External Pages >> Different car >> Section 2072 (Engine Mechanical) >> Preparation >> Special Service Tools
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Special Service Tools

WARNING: This page is about a different car, the 2008 Nissan Maxima. However, it is still accessible from the selected car via links, so may be relevant.

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

SPECIAL SERVICE TOOLS SPECIFICATION

Tool number
(Kent-Moore No.)
Tool name		 Description
ST0501S000
(-)
Engine stand assembly
1 ST05011000
(-)
Engine stand
2 ST05012000
(-)
Base
G04893953Courtesy of NISSAN MOTOR CO., U.S.A.
 Disassembling and assembling
KV101J0010
(J-47242)
Engine support table
G04885913Courtesy of NISSAN MOTOR CO., U.S.A.
 Engine and transmission assembly removal
KV10106500
(-)
Engine stand shaft
G04885653Courtesy of NISSAN MOTOR CO., U.S.A.
  
KV10117000
(J-41262)
Engine sub-attachment
G04885915Courtesy of NISSAN MOTOR CO., U.S.A.
 KV10117000 has been replaced with
KV10117001 (KV10117000 is no longer in production, but it is usable).
KV10117001
(-)
Engine sub-attachment
G04914638Courtesy of NISSAN MOTOR CO., U.S.A.
 Installing on the cylinder block
ST10120000
(J-24239-01)
Cylinder head bolt wrench
G04878220Courtesy of NISSAN MOTOR CO., U.S.A.
 Loosening and tightening cylinder head bolt
a: 13(0.51)dia  .
b: 12 (0.47) 
c: 10 (0.39) 
Unit: mm (in)
KV10116200
(J-26336-B)
Valve spring compressor
1 KV10115900
(J-26336-20)
Attachment
2 KV1019230
(-)
G04878205Courtesy of NISSAN MOTOR CO., U.S.A.
 Disassembling valve mechanism
Part (1) is a component of KV10116200 (J-26336-B), but Part (2) is not.
KV10107902
(J-38959)
Valve oil seal puller
G04899627Courtesy of NISSAN MOTOR CO., U.S.A.
 Removing valve oil seal
-
(J-39386)
Valve oil seal drift
G04878207Courtesy of NISSAN MOTOR CO., U.S.A.
 Installing valve oil seal
EM03470000
(J-8037)
Piston ring compressor
G04878208Courtesy of NISSAN MOTOR CO., U.S.A.
 Installing piston assembly into cylinder bore
ST16610001
(J-23907)
Pilot bushing puller
G04878209Courtesy of NISSAN MOTOR CO., U.S.A.
 Removing crankshaft pilot bushing
KV991J0120
(J-47128)
Seal installer
G04910978Courtesy of NISSAN MOTOR CO., U.S.A.
 Installing rear main seal
KV10111100
(J-37228)
Seal cutter
G04874707Courtesy of NISSAN MOTOR CO., U.S.A.
 Removing steel oil pan and rear timing chain case
WS39930000
(-)
Tube presser
G04878211Courtesy of NISSAN MOTOR CO., U.S.A.
 Pressing the tube of liquid gasket
KV10112100
(BT-8653-A)
Angle wrench
G04878212Courtesy of NISSAN MOTOR CO., U.S.A.
 Tightening bolts for bearing cap, cylinder head, etc.
KV991J0050
(J-44626)
Air fuel sensor Socket
G04899623Courtesy of NISSAN MOTOR CO., U.S.A.
 Loosening or tightening air fuel ratio A/F sensor a: 22 mm (0.87 in) 
KV10114400
(J-38365)
Heated oxygen sensor wrench
G04878214Courtesy of NISSAN MOTOR CO., U.S.A.
 Loosening or tightening rear heated oxygen sensor a: 22 mm (0.87 in) 
KV10117700
(J-44716)
Ring gear stopper
G04893964Courtesy of NISSAN MOTOR CO., U.S.A.
 Removing and installing crankshaft pulley
KV10109300
(-)
Pulley holder
G04885667Courtesy of NISSAN MOTOR CO., U.S.A.
 Removing and installing crankshaft pulley a: 68 mm (2.68 in) b: 8 mm (0.31 in) 
KV991J0100
(J-46531)
T55 Torx® Bit
G04914653Courtesy of NISSAN MOTOR CO., U.S.A.
 Removing and installing A/T drive plate and M/T flywheel bolts
scientia non olet · About LEMON Manuals