LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2004 >> Sentra SE-R >> Repair and Diagnosis >> External Pages >> Different car >> Section 212 (Engine Controls - Removal & Installation) >> Torque Specifications
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Torque Specifications

WARNING: This page is about a different car, the 2003 Nissan Altima. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS

Application (1) Ft. Lbs. (N.m)
Back-Up Lamp Switch 17-24 (22.5-33.3)
Clutch Interlock Switch Lock Nut 9-12 (12-15)
Engine Coolant Temperature Sensor
2.5L 15-21 (20-29)
3.5L (2)
Fuel Pump Locking Ring 23-26 (31-35)
Fuel Tube Assembly Bolts (3.5L) (3)
Fuel Tube Mounting Nuts (2.5L) (3)
Heated Oxygen Sensor
2.5L 30-36 (40-50)
3.5L 30-44 (40-60)
Intake Manifold Collector Bolts 13-15 (18-21)
Knock Sensor Bolt 12-19 (16-26)
Park/Neutral Position Switch 17-24 (22.5-33.3)
Spark Plug
2.5L 15-21 (19.6-29.4)
3.5L 14-22 (20-29)
Wiper Arm Nuts (Front Wipers) 16-19 (20.6-26.5)
INCH Lbs. (N.m) 
Intake Manifold Collector Bolts 13-15 (18-21)
Intake Manifold Collector Bolts 13-15 (18-21)
Accelerator Pedal Nuts 38-52 (4.3-5.9)
Camshaft Position Sensor
2.5L 48-65 (5.4-7.3)
3.5L 75-95 (8.5-10.7)
Crankshaft Position Sensor
2.5L 48-64 (5.4-7.3)
3.5L 75-95 (8.5-10.7)
Electronic Throttle Control Actuator (4)
EVAP Canister Mounting Bolts 45.1-56.4 (5.1-6.3)
EVAP Canister Purge Volume Control Solenoid Bolt
2.5L 43-51 (4.8-5.8)
3.5L 87-112 (9.81-12.7)
Fuel Injector Retainer Bolt
2.5L 46-64 (5.4-7.3)
3.5L 57-66 (6.37-7.54)
Fuel Damper Bolts (2.5L)
Right Side 74-100 (8.3-11.3)
Left Side 75-98 (8.5-11)
Fuel Rail Stud (2.5L) 87-104 (10-11)
Mass Air Flow Bolts 33-46 (3.8-5.2)
Rubber Hose Clamps 8.7-13.0 (1.0-1.5)
Wiper Motor Bolts 33.9-45.1 (3.8-5.1)
(1) If model is not indicated specification applies to both the 2.5L & 3.5L.
(2) Manufacture did not supply torque specifications.
(3) Tighten in order right front, left front, right rear, left rear, in 2 steps. First step 6.2-7.9 ft. lbs. (9.3-10.8 N.m). Second step 16-19 ft. lbs. (20.6-26.5 N.m).
(4) When tightening the mounting bolts of the electric throttle control actuator tighten them equally and diagonally in several steps. Tighten bolts to 64-84 inch lbs. (7.2-9.6 N.m).