LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2004 >> Sentra SE-R >> Repair and Diagnosis >> External Pages >> Different car >> Section 894 (Power Mirror Control System - Diagnosis) >> Mirror Position Sensor Circuit (W/ Memory) >> Inspection Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Inspection Procedure

WARNING: This page is about a different car, the 2004 Lexus ES 330. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK OUTER REAR VIEW MIRROR ASSY LH (FROM UPPERMOST POSITION TO LOWERMOST POSITION MIRROR SENSORS VOLTAGE) 
    1. Check the mirror position sensors operation.
      1. Connect the positive lead from the voltmeter to terminal VSSR (M3-2) and the negative lead to terminal E1 (M3-8).
      2. Check that the voltage gradually changes according to Fig 2 below while the mirror moves from the uppermost position to lowermost position.
        Fig 1: Checking Outer Rear View Mirror Assy LH
        G01437132Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Standard 

        Fig 2: Outer Rear View Mirror LH Standard Voltage Specification Chart
        G01437131Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        NG: REPLACE OUTER REAR VIEW MIRROR ASSY LH 

        OK: Go to next step. 

  2. CHECK OUTER REAR VIEW MIRROR ASSY LH (FROM LEFT-MOST POSITION TO RIGHT-MOST POSITION MIRROR SENSORS VOLTAGE) 
    1. Check the mirror position sensors operation.
      1. Connect the positive lead from the voltmeter to terminal HSRL (M3-7) and the negative lead to terminal E1 (M3-8).
      2. Check that the voltage gradually changes according to Fig 4 below while the mirror moves from the left-most position to right-most position.
        Fig 3: Checking Outer Rear View Mirror Assy LH
        G01437134Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Standard 

        Fig 4: Outer Rear View Mirror LH Standard Voltage Specification Chart
        G01437133Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        NG: REPLACE OUTER REAR VIEW MIRROR ASSY LH 

        OK: Go to next step. 

  3. CHECK WIRE HARNESS (OUTER MIRROR CONTROL ECU - OUTER REAR VIEW MIRROR LH) 
    1. Disconnect the M3 outer rear view mirror and M2 outer mirror control ECU connectors.
    2. Check the continuity between connectors.
      Fig 5: Checking Wire Harness
      G01437136Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard 

      Fig 6: Wire Harness Continuity Specification Chart
      G01437135Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      NG: REPAIR OR REPLACE WIRE HARNESS AND CONNECTOR 

      OK: REPLACE OUTER MIRROR CONTROL ECU ASSY 

  4. CHECK OUTER REAR VIEW MIRROR ASSY RH (FROM UPPERMOST POSITION TO LOWERMOST POSITION MIRROR SENSORS VOLTAGE) 
    1. Check the mirror position sensors operation.
      1. Connect the positive lead from the voltmeter to terminal VSSR (2) and the negative lead to terminal E1 (8).
      2. Check that the voltage gradually changes according to Fig 8 below while the mirror moves between the uppermost position and lowermost position.
        Fig 7: Checking Outer Rear View Mirror Assy RH
        G01437138Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Standard 

        Fig 8: Outer Rear View Mirror RH Standard Voltage Specification Chart
        G01437137Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        NG: REPLACE OUTER REAR VIEW MIRROR ASSY RH 

        OK: Go to next step. 

  5. CHECK OUTER REAR VIEW MIRROR ASSY RH (FROM UPPERMOST POSITION TO LOWERMOST POSITION MIRROR SENSORS VOLTAGE) 
    1. Check the mirror potion sensors operation.
      1. Connect the positive lead from the voltmeter to terminal HSSR (7) and the negative lead to terminal E1 (8).
      2. Check that the voltage gradually changes according to the Fig 10 below while the mirror moves between the left-most position and right-most position.
        Fig 9: Checking Outer Rear View Mirror Assy RH
        G01437140Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Standard 

        Fig 10: Outer Rear View Mirror RH Standard Voltage Specification Chart
        G01437139Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        NG: REPLACE OUTER REAR VIEW MIRROR ASSY RH 

        OK: Go to next step. 

  6. CHECK WIRE HARNESS (OUTER MIRROR CONTROL ECU - OUTER REAR VIEW MIRROR RH) 
    1. Disconnect the M4 outer rear view mirror and M2 outer mirror control ECU connectors.
    2. Check the continuity between connectors.
      Fig 11: Checking Wire Harness
      G01437142Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard 

      Fig 12: Wire Harnesss Continuity Specification Chart
      G01437141Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      NG: REPAIR OR REPLACE WIRE HARNESS AND CONNECTOR 

      OK: REPLACE OUTER MIRROR CONTROL ECU ASSY