LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2007 >> X-Trail LE >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System - Introduction >> Trouble Diagnosis >> CONSULT-II Function (ENGINE) >> Data Monitor Mode >> Monitored Item
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Monitored Item

DATA MONITOR REFERENCE CHART

x: Applicable
Monitored item [Unit] ECM INPUT SIGNALS MAIN SIGNALS Description Remarks
ENG SPEED [rpm] x x
  • Indicates the engine speed computed from the signals of the crankshaft position sensor (POS) and camshaft position sensor (PHASE).
  • Accuracy becomes poor if engine speed drops below the idle rpm.
  • If the signal is interrupted while the engine is running, an abnormal value may be indicated.
MAS A/F SE-B1 [V] x x
  • The signal voltage of the mass air flow sensor is displayed.
  • When the engine is stopped, a certain value is indicated.
B/FUEL SCHDL [msec]   x
  • "Base fuel schedule" indicates the fuel injection pulse width programmed into ECM, prior to any learned on board correction.
  
A/F ALPHA-B1 [%]   x
  • The mean value of the air-fuel ratio feedback correction factor per cycle is indicated.
  • When the engine is stopped, a certain value is indicated.
  • This data also includes the data for the air-fuel ratio learning control.
COOLAN TEMP/S [°C] or [°F] x x
  • The engine coolant temperature (determined by the signal voltage of the engine coolant temperature sensor) is displayed.
  • When the engine coolant temperature sensor is open or short-circulated, ECM enters fail-safe mode. The engine coolant temperature determined by the ECM is displayed.
HO2S1 (B1) [V] x x
  • The signal voltage of the heated oxygen sensor 1 is displayed.
  
HO2S2 (B1) [V] x x
  • The signal voltage of the heated oxygen sensor 2 is displayed.
  
HO2S1 MNTR (B1) [RICH/LEAN] x x
  • Display of heated oxygen sensor 1 signal during air-fuel ratio feedback control:
RICH: Means the mixture became rich, and control is being affected toward a leaner mixture.LEAN: Means the mixture became lean, and control is being affected toward a rich mixture.
  • After turning ON the ignition switch, "RICH" is displayed until air-fuel mixture ratio feedback control begins.
  • When the air-fuel ratio feedback is clamped, the value just before the clamping is displayed continuously.
HO2S2 MNTR (B1) [RICH/LEAN] x  
  • Display of heated oxygen sensor 2 signal:
RICH: Means the amount of oxygen after three way catalyst is relatively small.LEAN: Means the amount of oxygen after three way catalyst is relatively large.
  • When the engine is stopped, a certain value is indicated.
VHCL SPEED SE [km/h] or [mph] x x
  • The vehicle speed computed from the vehicle speed signal is displayed.
  
BATTERY VOLT [V] x x
  • The power supply voltage of ECM is displayed.
  
ACCEL SEN 1 [V] x x
  • The accelerator pedal position sensor signal voltage is displayed.
  • ACCEL SEN 2 signal is converted by ECM internally. Thus, it differs from ECM terminal voltage signal.
ACCEL SEN 2 [V] x      
THRTL SEN 1 [V] x x
  • The throttle position sensor signal voltage is displayed.
  • THRTL SEN 2 signal is converted by ECM internally. Thus, it differs from ECM terminal voltage signal.
THRTL SEN 2 [V] x      
FUEL T/TEMP SE [°C] or [°F] x  
  • The fuel temperature (determined by the signal voltage of the fuel tank temperature sensor) is displayed.
  
INT/A TEMP SE [°C] or [°F] x x
  • The intake air temperature (determined by the signal voltage of the intake air temperature sensor) is indicated.
  
EVAP SYS PRES [V] x  
  • The signal voltage of EVAP control system pressure sensor is displayed.
  
FUEL LEVEL SE [V] x  
  • The signal voltage of the fuel level sensor is displayed.
  
START SIGNAL [ON/OFF] x x
  • Indicates [ON/OFF] condition from the starter signal.
  • After starting the engine, [OFF] is displayed regardless of the starter signal.
CLSD THL POS [ON/OFF] x x
  • Indicates idle position [ON/OFF] computed by ECM according to the accelerator pedal position sensor signal.
  
AIR COND SIG [ON/OFF] x x
  • Indicates [ON/OFF] condition of the air conditioner switch as determined by the air conditioner signal.
  
P/N POSI SW [ON/OFF] x x
  • Indicates [ON/OFF] condition from the park/neutral position (PNP) switch signal.
  
PW/ST SIGNAL [ON/OFF] x x
  • [ON/OFF] condition of the power steering system (determined by the signal voltage of the power steering pressure sensor signal) is indicated.
  
LOAD SIGNAL [ON/OFF] x x
  • Indicates [ON/OFF] condition from the electrical load signal.
ON: Rear window defogger switch is ON and/or lighting switch is in 1st or 2nd position and/or heater fan switch is ON.OFF: Rear window defogger switch and lighting switch and heater fan switch are OFF.		  
SNOW MODE SW(1) [ON/OFF]    
  • Indicates [NO/OFF] condition from the snow mode switch signal.
  
IGNITION SW [ON/OFF] x x
  • Indicates [ON/OFF] condition from ignition switch.
  
HEATER FAN SW [ON/OFF] x  
  • Indicates [ON/OFF] condition from the heater fan switch signal.
  
BRAKE SW [ON/OFF] x  
  • Indicates [ON/OFF] condition from the stop lamp switch signal.
  
INJ PULSE-B1 [msec]   x
  • Indicates the actual fuel injection pulse width compensated by ECM according to the input signals.
  • When the engine is stopped, a certain computed value is indicated.
IGN TIMING [BTDC]   x
  • Indicates the ignition timing computed by ECM according to the input signals.
  • When the engine is stopped, a certain value is indicated.
CAL/LD VALUE [%]    
  • "Calculated load value" indicates the value of the current airflow divided by peak airflow.
  
MASS AIRFLOW [g.m/s]    
  • Indicates the mass airflow computed by ECM according to the signal voltage of the mass air flow sensor.
  
PURG VOL C/V [%]    
  • Indicates the EVAP canister purge volume control solenoid valve control value computed by the ECM according to the input signals.
  • The opening becomes larger as the value increases.
  
INT/V TIM (B1) [°CA]    
  • Indicates [°CA] of intake camshaft advanced angle.
  
INT/V SOL (B1) [%]    
  • The control value of the intake valve timing control solenoid valve (determined by ECM according to the input signal) is indicated.
  • The advance angle becomes larger as the value increases.
  
VIAS S/V [ON/OFF]    
  • The control condition of the VIAS control solenoid valve (determined by ECM according to the input signals) is indicated.
ON: VIAS control solenoid valve is operating.OFF: VIAS control solenoid valve is not operating.		  
AIR COND RLY [ON/OFF]   x
  • The air conditioner relay control condition (determined by ECM according to the input signals) is indicated.
  
FUEL PUMP RLY [ON/OFF]   x
  • Indicates the fuel pump relay control condition determined by ECM according to the input signals.
  
VENT CONT/V [ON/OFF]    
  • The control condition of the EVAP canister vent control valve (determined by ECM according to the input signals) is indicated.
ON: ClosedOFF: Open		  
THRTL RELAY [ON/OFF]   x
  • Indicates the throttle control motor relay control condition determined by the ECM according to the input signals.
  
COOLING FAN [HI/LOW/OFF]   x
  • Indicates the condition of the cooling fan (determined by ECM according to the input signals).
HI: High speed operationLOW: Low speed operationOFF: Stop		  
HO2S1 HTR (B1) [ON/OFF]    
  • Indicates [ON/OFF] condition of heated oxygen sensor 1 heater determined by ECM according to the input signals.
  
HO2S2 HTR (B1) [ON/OFF]    
  • Indicates [ON/OFF] condition of heated oxygen sensor 2 heater determined by ECM according to the input signals.
  
IDL A/V LEARN [YET/CMPLT]    
  • Display the condition of Idle Air Volume Learning
YET: Idle Air Volume Learning has not been performed yet.CMPLT: Idle Air Volume Learning has already been performed successfully.		  
TRVL AFTER MIL [km] or [mile]    
  • Distance traveled while MIL is activated.
  
O2SEN HTR DTY [%]    
  • Indicates the heated oxygen sensor 1 heater control value computed by the ECM according to the input signals.
  
AC PRESS SEN [V]    
  • The signal voltage from the refrigerant pressure sensor is displayed.
  
VHCL SPEED SE [km/h] or [mph]    
  • The vehicle speed computed from the vehicle speed signal sent from TCM is displayed.
  
SET VHCL SPD [km/h] or [mph]    
  • The preset vehicle speed is displayed.
  
MAIN SW [ON/OFF]    
  • Indicates [ON/OFF] condition from MAIN (CRUISE) switch signal.
  
CANCEL SW [ON/OFF]    
  • Indicates [ON/OFF] condition from CANCEL switch signal.
  
RESUME/ACC SW [ON/OFF]    
  • Indicates [ON/OFF] condition from RESUME/ACCEL switch signal.
  
SET SW [ON/OFF]    
  • Indicates [ON/OFF] condition from SET/COAST switch signal.
  
BRAKE SW1 [ON/OFF]    
  • Indicates [ON/OFF] condition from ASCD brake switch signal, and ASCD clutch switch signal (M/T models).
  
BRAKE SW2 [ON/OFF]    
  • Indicates [ON/OFF] condition of stop lamp switch signal.
  
VHCL SPD CUT [NON/CUT]    
  • Indicates the vehicle cruise condition.
NON: Vehicle speed is maintained at the ASCD set speed.CUT: Vehicle speed increased to excessively high compared with the ASCD set speed, and ASCD operation is cut off.		  
LO SPEED CUT [NON/CUT]    
  • Indicates the vehicle cruise condition.
NON: Vehicle speed is maintained at the ASCD set speed.CUT: Vehicle speed decreased to excessively low compared with the ASCD set speed, and ASCD operation is cut off.		  
AT OD MONITOR [ON/OFF]    
  • Indicates [ON/OFF] condition of A/T O/D according to the input signal from the TCM.
  
AT OD CANCEL [ON/OFF]    
  • Indicates [ON/OFF] condition of A/T O/D cancel signal sent from the TCM.
  
CRUISE LAMP [ON/OFF]    
  • Indicates [ON/OFF] condition of CRUISE lamp determined by the ECM according to the input signals.
  
SET LAMP [ON/OFF]    
  • Indicates [ON/OFF] condition of SET lamp determined by the ECM according to the input signals.
  
Voltage [V]    
  • Voltage, frequency, duty cycle or pulse width measured by the probe.
  • Only "#" is displayed if item is unable to be measured.
  • Illustrations with "#"s are temporary ones. They are the same illustrations as an actual piece of data which was just previously measured.
Frequency [msec], [Hz] or [%]    
DUTY-HI    
DUTY-LOW    
PLS WIDTH-HI    
PLS WIDTH-LOW    
(1) With 2WD models.
NOTE: Any monitored item that does not match the vehicle being diagnosed is deleted from the display automatically.
scientia non olet · About LEMON Manuals