XM Sat Subscription Status

The XM NavTraffic subscription status can be checked.

Error History

The self-diagnosis results are judged depending on whether any error occurs from when "Self-diagnosis" is selected until the self-diagnosis results are displayed.

However, the diagnosis results are judged normal if an error has occurred before the ignition switch is turned ON and then no error has occurred until the self-diagnosis start. Check the "Error Record" to detect any error that may have occurred before the self-diagnosis start because of this situation.

The error record displays the time and place of the most recent occurrence of that error. However, take note of the following points.

• If there is a malfunction with the GPS antenna circuit board in the AV control unit, the correct date and time of occurrence may not be able to be displayed.
• Place of the error occurrence is represented by the position of the current location mark at the time the error occurred. If the current location mark has deviated from the correct position, then the place of the error occurrence cannot be correctly located.
• The frequency of occurrence is displayed in a count up manner. The actual count up method differs depending on the error item.

Count up method A

• The counter resets to 0 if an error occurs when IGN switch is turned ON. The counter increases by 1 if the condition is normal at a next IGN ON cycle.
• The counter upper limit is 39. Any counts exceeding 39 are ignored. The counter can be reset (no error record display) with the "Delete log" switch or CONSULT-III.

Count up method B

• The counter increases by 1 if an error occurs when IGN switched is ON. The counter will not decrease even if the status is normal at the next IGN ON cycle.
• The counter upper limit is 50. Any counts exceeding 50 are ignored. The counter can be reset (no error record display) with the "Delete log" switch or CONSULT-III.

Display type of occurrence frequency	Error history display item
Count up method A	CAN communication line, control unit (CAN), AV communication line, control unit (AV communication)
Count up method B	Other than the above

Error item

Some error items may be displayed simultaneously according to the cause. If some error items are displayed simultaneously, the detection of the cause can be performed by the combination of display items

Error item	Description	Possible malfunction factor/Action to take
CAN COMM CIRCUIT	CAN communication malfunction is detected.	Perform diagnosis with CONSULT-III, and then repair the malfunctioning parts according to the diagnosis results. Refer to "CONSULT-III FUNCTION (MULTI AV) ".
CONTROL UNIT (CAN)	CAN initial diagnosis malfunction is detected.	Replace the AV control unit.
CONTROL UNIT (AV)	AV communication circuit initial diagnosis malfunction is detected.
FLASH-ROM Error Of Control Unit	AV control unit malfunction is detected.
Connection Of Gyro
XM SERIAL COMM Error
CAN Controller Memory Error
Bluetooth Module Connection Error
HDD CONN Error
HDD READ Error
HDD WRITE Error
HDD COMM Error
HDD ACCESS Error
DSP CONN Error
DSP COMM Error
Internal Communication Error	Malfunction is detected in AV control unit power supply and ground circuits.	Check AV control unit power supply and ground circuits. When detecting no malfunction in those components, replace AV control unit.
GPS Communication Error	GPS malfunction is detected.	An intermittent error caused by strong radio interference may be detected unless a symptom (GPS reception error, etc.) occurs. Replace the AV control unit if the malfunction occurs constantly.
GPS ROM Error
GPS RAM Error
GPS RTC Error
Front Display Connection Error	When either one of the following items are detected: front display unit power supply and ground circuits are malfunctioning. serial communication circuits between AV control unit and front display unit are malfunctioning. serial communication signal between AV control unit and front display unit is malfunctioning.	Front display unit power supply and ground circuits. Serial communication circuits between AV control unit and display unit.
GPS Antenna Error	GPS antenna connection malfunction is detected.	GPS antenna.
XM Antenna Connection Error	Satellite radio antenna connection malfunction is detected.	Satellite radio antenna feeder. Satellite radio antenna.
AV COMM CIRCUIT Internal Communication Error	Malfunction is detected in AV control unit power supply and ground circuits.	Check AV control unit power supply and ground circuits. When detecting no malfunction in those components, replace AV control unit.
AV COMM CIRCUIT Switches Connection Error	When either one of the following items are detected: multifunction switch power supply and ground circuits are malfunctioning. AV communication circuits between AV control unit and multifunction switch are malfunctioning. AV communication signal between AV control unit and multifunction switch is malfunctioning.	Multifunction switch power supply and ground circuits. AV communication circuits between AV control unit and multifunction switch.
AV COMM CIRCUIT iPod Connection Error	When either one of the following items are detected: iPod adapter power supply and ground circuits are malfunctioning. AV communication circuits between multifunction switch and iPod adapter are malfunctioning. AV communication signal between AV control unit and iPod adapter is malfunctioning.	iPod adapter power supply and ground circuits. AV communication circuits between multifunction switch unit and iPod adapter.
AV COMM CIRCUIT Switches Connection Error iPod Connection Error	Malfunction is detected in AV communication circuits between AV control unit and multifunction switch.	AV communication circuits between AV control unit and multifunction switch.

Vehicle CAN Diagnosis

• CAN communication status and error counter is displayed.
• The error counter displays "OK" if any malfunction was not detected in the past and displays "0" if a malfunction is detected. It increases by 1 if the status is normal at the next ignition switch ON cycle. The upper limit of the counter is 39.
• The error counter is erased if "Reset" is pressed.
  Fig 3: Display - Vehicle CAN Diagnosis Screen

  Courtesy of NISSAN MOTOR CO., U.S.A.
  DISPLAY REFERENCE CHART
  
  

  Items	Display (Current)	Malfunction counter (Past)
  Tx (HVAC)	OK / UNKWN	OK / 0 - 39
  Rx (ECM)	OK / UNKWN	OK / 0 - 39
  Rx (Cluster)	OK / UNKWN	OK / 0 - 39
  Rx (BCM)	OK / UNKWN	OK / 0 - 39
  Rx (HVAC)	OK / UNKWN	OK / 0 - 39
  Rx (USM)	OK / UNKWN	OK / 0 - 39

AV COMM Diagnosis

• Displays the communication status between AV control unit (master unit) and each unit.
• The error counter displays "OK" if any malfunction was not detected in the past and displays "0" if a malfunction is detected. It increases by 1 if the condition is normal at the next ignition switch ON cycle. The upper limit of the counter is 39.
• The error counter is erased if "Reset" is pressed.
  Fig 4: Display - AV COMM Diagnosis Screen

  Courtesy of NISSAN MOTOR CO., U.S.A.
  DISPLAY REFERENCE CHART
  
  

  Items	Status (Current)	Counter (Past)
  C Tx(ITM-PrimarySW)	OK / UNKWN	OK / 0 - 39
  C Rx(PrimarySW-ITM)	OK / UNKWN	OK / 0 - 39
  C Rx(STRG SW-ITM)	OK / UNKWN	OK / 0 - 39
  C Rx(Audio-ITM)	OK / UNKWN	OK / 0 - 39
  C Rx(Amp-ITM)	OK / UNKWN	OK / 0 - 39
  C Rx(XM-ITM)	OK / UNKWN	OK / 0 - 39
  C Rx(iPod-ITM)	OK / UNKWN	OK / 0 - 39
  C Rx(Amp-Audio)	-	-
  C Rx(iPod-Audio)	OK / UNKWN	OK / 0 - 39
  C Tx(Audio-ITM)	OK / UNKWN	OK / 0 - 39
  NOTE: Any units with "-" displayed have no history of vehicle connection. "Audio" and "Amp" indicate the same status because "Amp" indicates the status of the amplifier integrated in the AV control unit. "STRG SW", "Amp", and "XM" indicate the same status as "Audio".

Hands-Free Phone

The hands-free phone reception volume adjustment, microphone and speaker test, and memory erase functions are also available.

Bluetooth

Confirm / Change Passkey

• The Bluetooth passkey can be confirmed and changed.
• The passkey can be changed by four digits within 0 to 9.
  Fig 6: Display - Confirm/Change Passkey Screen

  Courtesy of NISSAN MOTOR CO., U.S.A.

Confirm / Change Device Name

• The Bluetooth device name be confirmed and changed.
• The device name can be changed by sixteen digits from A to Z (small characters can be used) and "-" (hyphens).
  Fig 7: Display - Confirm/Change Device Name

  Courtesy of NISSAN MOTOR CO., U.S.A.

SAT

• Change Channel
  • Any necessary channels required to receive traffic information from the satellite radio system can be set.
    Fig 8: Display - Change Channel Screen

    Courtesy of NISSAN MOTOR CO., U.S.A.
• Change Application ID
  • Any application ID'-s required to receive traffic information from the satellite radio system can be set.
    Fig 9: Display - Change Application ID Screen

    Courtesy of NISSAN MOTOR CO., U.S.A.

Delete Unit Connection Log

Deletes any unit connection records and error records from the AV control unit memory. (Clear the records of the unit that has been removed.)

Initialize Settings

Deletes data stored in HDD.