LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2009 >> Rogue SL, FWD >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System (MEXICO) >> Component Diagnosis >> P2135 TP Sensor >> Diagnosis Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnosis Procedure

  1. CHECK GROUND CONNECTION
    1. Turn ignition switch OFF.
    2. Check ground connection E21. Refer to Ground Inspection in "CIRCUIT INSPECTION ".

      Is the inspection result normal? 

      YES: GO TO 2.

      NO: Repair or replace ground connection.

  2. CHECK THROTTLE POSITION SENSOR POWER SUPPLY CIRCUIT-I
    1. Disconnect electric throttle control actuator harness connector.
    2. Turn ignition switch ON.
    3. Check the voltage between electric throttle control actuator harness connector and ground.
      CONNECTOR TERMINAL VOLTAGE CHART

      Electric throttle control actuator Ground Voltage
      Connector Terminal
      F29 1 Ground Approx. 5 V

      Is the inspection result normal? 

      YES: GO TO 3.

      NO: Repair open circuit or short to ground or short to power in harness or connectors.

  3. CHECK THROTTLE POSITION SENSOR POWER SUPPLY CIRCUIT-II
    1. Turn ignition switch OFF.
    2. Disconnect ECM harness connector.
    3. Check the continuity between electric throttle control actuator harness connector and ground.
      CONNECTOR TERMINAL CONTINUITY CHART

      Electric throttle control actuator ECM Continuity
      Connector Terminal Connector Terminal
      F29 1 F8 47 Existed

      Is the inspection result normal? 

      YES: GO TO 4.

      NO: Repair open circuit.

  4. CHECK THROTTLE POSITION SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
    1. Turn ignition switch OFF.
    2. Disconnect ECM harness connector.
    3. Check the continuity between electric throttle control actuator harness connector and ground.
      CONNECTOR TERMINAL CONTINUITY CHART

      Electric throttle control actuator ECM Continuity
      Connector Terminal Connector Terminal
      F29 4 F8 36 Existed
    4. Also check harness for short to ground and short to power.

      Is the inspection result normal? 

      YES: GO TO 5.

      NO: Repair open circuit or short to ground or short to power in harness or connectors.

  5. CHECK SENSOR POWER SUPPLY CIRCUIT

    Check harness for short to power and short to ground, between the following terminals.

    ECM REFERENCE

    ECM Sensor
    Connector Terminal Name Connector Terminal
    F8 47 Electric throttle control actuator F29 1
    59 CMP sensor (PHASE) F26 1
    E16 83 APP sensor E110 4

    Is the inspection result normal? 

    YES: GO TO 6.

    NO: Repair short to ground or short to power in harness or connectors.

  6. CHECK THROTTLE POSITION SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
    1. Check the continuity between electric throttle control actuator harness connector and ground.
      CONNECTOR TERMINAL CONTINUITY CHART

      Electric throttle control actuator ECM Continuity
      Connector Terminal Connector Terminal
      F29 2 F8 37 Existed
      3 38
    2. Also check harness for short to ground and short to power.

      Is the inspection result normal? 

      YES: GO TO 7.

      NO: Repair open circuit or short to ground or short to power in harness or connectors.

  7. CHECK THROTTLE POSITION SENSOR

    Refer to "COMPONENT INSPECTION ".

    Is the inspection result normal? 

    YES: GO TO  9.

    NO: GO TO 8.

  8. REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
    1. Replace electric throttle control actuator.
    2. Go to "SPECIAL REPAIR REQUIREMENT ".

      INSPECTION END

  9. CHECK INTERMITTENT INCIDENT

    Refer to "INTERMITTENT INCIDENT ".

    INSPECTION END

scientia non olet · About LEMON Manuals