INTELLIGENT KEY: CONSULT-III Function (BCM - INTELLIGENT KEY)

WORK SUPPORT

MONITOR ITEM DESCRIPTION CHART

Monitor item	Description
CONFIRM KEY FOB ID	It can be checked whether Intelligent Key ID code is registered or not in this mode
AUTO LOCK SET	Auto door lock time can be changed in this mode MODE 1: OFF MODE 2: 30 sec MODE 3: 1 minute MODE 4: 2 minutes MODE 5: 3 minutes MODE 6: 4 minutes MODE 7: 5 minutes
LOCK/UNLOCK BY I-KEY	Door lock/unlock function by door request switch mode can be changed to operation in this mode On: Operate Off: Non-operation
ENGINE START BY I-KEY	Engine start function mode can be changed to operation with this mode On: Operate Off: Non-operation
TRUNK/GLASS HATCH OPEN	NOTE: This item is displayed, but cannot be monitored
PANIC ALARM SET	Panic alarm button pressing time on Intelligent Key remote control button can be selected from the following with this mode MODE 1: 0.5 sec MODE 2: Non-operation MODE 3: 1.5 sec
TRUNK OPEN DELAY	NOTE: This item is displayed, but cannot be monitored
LO-BATT OF KEY FOB WARN	Intelligent Key low battery warning mode can be changed to operation with this mode On: Operate Off: Non-operation
ANTI KEY LOCK IN FUNCTI	Key reminder function mode can be changed to operation with this mode On: Operate Off: Non-operation
HAZARD ANSWER BACK	Hazard reminder function mode by door request switch and Intelligent Key button can be selected from the following with this mode Lock Only: Door lock operation only Unlock Only: Door unlock operation only Lock/Unlock: Lock/unlock operation Off: Non-operation
ANS BACK I-KEY LOCK	Buzzer reminder function (lock operation) mode by door request switch (driver side and passenger side) can be selected from the following with this mode Horn Chirp: Sound horn Buzzer: Sound Intelligent Key warning buzzer Off: Non-operation
ANS BACK I-KEY UNLOCK	Buzzer reminder function (unlock operation) mode by door request switch can be changed to operation with this mode On: Operate Off: Non-operation
SHORT CRANKING OUTPUT	Starter motor can operate during the times below
INSIDE ANT DIAGNOSIS	This function allows inside key antenna self-diagnosis
HORN WITH KEYLESS LOCK	Horn reminder function mode by Intelligent Key button can be changed to operate (ON) or not operate (OFF) with this mode On: Operate Off: Non-operation

SELF-DIAG RESULT

Refer to "DTC INDEX ".

DATA MONITOR

MONITOR ITEM CONDITION CHART

Monitor Item

Condition

REQ SW-DR

Indicates [On/Off] condition of door request switch (driver side)

REQ SW-AS

Indicates [On/Off] condition of door request switch (passenger side)

REQ SW-BD/TR

Indicates [On/Off] condition of back door request switch

PUSH SW

Indicates [On/Off] condition of push-button ignition switch

CLUTCH SW⁽¹⁾

Indicates [On/Off] condition of clutch switch

BRAKE SW 1

Indicates [On/Off]⁽²⁾ condition of brake switch power supply

BRAKE SW 2

Indicates [On/Off] condition of brake switch

DETE/CANCL SW

Indicates [On/Off] condition of P position

SFT PN/N SW

Indicates [On/Off] condition of P or N position

S/L-LOCK

NOTE: This item is displayed, but cannot be monitored

S/L-UNLOCK

NOTE: This item is displayed, but cannot be monitored

S/L RELAY-F/B

NOTE: This item is displayed, but cannot be monitored

UNLK SEN-DR

Indicates [On/Off] condition of driver door UNLOCK status

PUSH SW-IPDM

Indicates [On/Off] condition of push-button ignition switch

IGN RLY1-F/B

Indicates [On/Off] condition of ignition relay 1

DETE SW-IPDM

Indicates [On/Off] condition of P position

SFT PN-IPDM

Indicates [On/Off] condition of P or N position

SFT P-MET

Indicates [On/Off] condition of P position

SFT N-MET

Indicates [On/Off] condition of N position

ENGINE STATE

Indicates [Stop/Stall/Crank/Run] condition of engine states

S/L LOCK-IPDM

NOTE: This item is displayed, but cannot be monitored

S/L UNLK-IPDM

NOTE: This item is displayed, but cannot be monitored

S/L RELAY-REQ

NOTE: This item is displayed, but cannot be monitored

VEH SPEED 1

Display the vehicle speed signal received from combination meter by numerical value [Km/h]

VEH SPEED 2

Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]

DOOR STAT-DR

Indicates [LOCK/READY/UNLK] condition of driver side door status

DOOR STAT-AS

Indicates [LOCK/READY/UNLK] condition of passenger side door status

ID OK FLAG

Indicates [Set/Reset] condition of key ID

PRMT ENG STRT

Indicates [Set/Reset] condition of engine start possibility

PRMT RKE STRT

NOTE: This item is displayed, but cannot be monitored

TRNK/HAT MNTR

NOTE: This item is displayed, but cannot be monitored

RKE-LOCK

Indicates [On/Off] condition of LOCK signal from Intelligent Key

RKE-UNLOCK

Indicates [On/Off] condition of UNLOCK signal from Intelligent Key

RKE-TR/BD

NOTE: This item is displayed, but cannot be monitored

RKE-PANIC

Indicates [On/Off] condition of PANIC button of Intelligent Key

RKE-MODE CHG

Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key

RKE OPE COUN1

When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the numerical value start changing

RKE OPE COUN2

NOTE: This item is displayed, but cannot be monitored

⁽¹⁾	It is displayed but does not operate on M/T models.

⁽²⁾	OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.

ACTIVE TEST

TEST ITEM DESCRIPTION CHART

Test item	Description
BATTERY SAVER	This test is able to check interior room lamp operation On: Operate Off: Non-operation
OUTSIDE BUZZER	This test is able to check Intelligent Key warning buzzer operation On: Operate Off: Non-operation
INSIDE BUZZER	This test is able to check warning chime in combination meter operation Take out: Take away warning chime sounds when CONSULT-III screen is touched Key: Key warning chime sounds when CONSULT-III screen is touched Knob: OFF position warning chime sounds when CONSULT-III screen is touched
INDICATOR	This test is able to check warning lamp operation KEY ON: "KEY" Warning lamp illuminates when CONSULT-III screen is touched "KEY" Warning lamp blinks when CONSULT-III screen is touched
INT LAMP	This test is able to check interior room lamp operation On: Operate Off: Non-operation
LCD	This test is able to check meter display information BP N: Engine start operation indicator lamp indicate when CONSULT-III screen is touched BP I: Engine start operation indicator lamp indicate when CONSULT-III screen is touched ID NG: This item is displayed, but cannot be monitored ROTAT: This item is displayed, but cannot be monitored SFT P: Shift P warning lamp indicate when CONSULT-III screen is touched INSRT: This item is displayed, but cannot be monitored BATT: Key warning lamp indicator when CONSULT-III screen is touched NO KY: This item is displayed, but cannot be monitored OUTKEY: Engine start operation indicator lamp indicate when CONSULT-III screen is touched LK WN: Engine start operation indicator lamp indicate when CONSULT-III screen is touched
FLASHER	This test is able to check security hazard lamp operation The hazard lamps are activated after "LH/RH/Off" on CONSULT-III screen is touched
HORN	This test is able to check horn operation The horn is activated after "ON" on CONSULT-III screen is touched
P RANGE	This test is able to check CVT shift selector power supply On: Operate Off: Non-operation
ENGINE SW ILLUMI	This test is able to check push-ignition switch illumination operation Push-ignition switch illumination illuminates when "ON" on CONSULT-III screen is touched
PUSH SWITCH INDICATOR	This test is able to check LOCK indicator in push-ignition switch operation LOCK indicator in push-ignition switch illuminates when "ON" on CONSULT-III screen is touched
TRUNK/BACK DOOR	NOTE: This item is displayed, but cannot be monitored