Diagnosis Procedure

Regarding Wiring Diagram information, refer to "WIRING DIAGRAM-ENGINE CONTROL SYSTEM- ".

1. CHECK GROUND CONNECTION
   1. Turn ignition switch OFF.
   2. Check ground connection E9. Refer to Ground Inspection in "CIRCUIT INSPECTION ".

      Is the inspection result normal? 

      YES >> GO TO 2.

      NO >> Repair or replace ground connection.

2. CHECK CONNECTOR
   1. Disconnect EVAP control system pressure sensor harness connector.
   2. Check that water is not inside connectors.

      Is the inspection result normal? 

      YES >> GO TO 3.

      NO >> Repair or replace harness connector.

3. CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR POWER SUPPLY CIRCUIT-I
   1. Turn ignition switch ON.
   2. Check the voltage between EVAP control system pressure sensor harness connector and ground.
      VOLTAGE REFERENCE CHART
      
      

      EVAP control system pressure sensor		Ground	Voltage (V)
      Connector	Terminal
      B41	3	Ground	Approx. 5

      Fig 1: Checking Voltage Between EVAP Control System Pressure Sensor Harness Connector And Ground

      Courtesy of NISSAN MOTOR CO., U.S.A.

      Is the inspection result normal? 

      YES >> GO TO  10.

      NO >> GO TO 4.

4. CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR POWER SUPPLY CIRCUIT-II
   1. Turn ignition switch OFF.
   2. Disconnect ECM harness connector.
   3. Check the continuity between EVAP control system pressure sensor harness connector and ECM harness connector.
      CONTINUITY CHART
      
      

      EVAP control system pressure sensor		ECM		Continuity
      Connector	Terminal	Connector	Terminal
      B41	3	E10	91	Existed

      Is the inspection result normal? 

      YES >> GO TO  6.

      NO >> GO TO 5.

5. DETECT MALFUNCTIONING PART

   Check the following.

   • Harness connectors B29, E29
   • Harness for open or short between EVAP control system pressure sensor and ECM

     Repair open circuit.

6. CHECK SENSOR POWER SUPPLY CIRCUIT

   Check harness for short to power and short to ground, between the following terminals.

   ECM CONNECTOR TERMINALS CHART
   
   

   ECM		Sensor
   Connector	Terminal	Name	Connector	Terminal
   F13	72	Refrigerant pressure sensor	E219	1
   	76	CKP sensor (POS)	F30	1
   E10	87	APP sensor	E40	6
   	91	EVAP control system pressure sensor	B41	3

   Is the inspection result normal? 

   YES >> GO TO 7.

   NO >> Repair short to ground or short to power in harness or connectors.

7. CHECK COMPONENTS

   Check the following.

   • Crankshaft position sensor (POS) (Refer to "COMPONENT INSPECTION ".)
   • Refrigerant pressure sensor (Refer to "DIAGNOSIS PROCEDURE ".)

     Is the inspection result normal? 

     YES >> GO TO 8.

     NO >> Replace malfunctioning components.

8. CHECK APP SENSOR

   Refer to "COMPONENT INSPECTION ".

   Is the inspection result normal? 

   YES >> GO TO  15.

   NO >> GO TO 9.

9. REPLACE ACCELERATOR PEDAL ASSEMBLY
   1. Replace accelerator pedal assembly. Refer to REMOVAL AND INSTALLATION .
   2. Refer to "SPECIAL REPAIR REQUIREMENT ".

      INSPECTION END

10. CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
    1. Turn ignition switch OFF.
    2. Disconnect ECM harness connector.
    3. Check the continuity between EVAP control system pressure sensor harness connector and ECM harness connector.
       CONTINUITY CHART
       
       

       EVAP control system pressure sensor		ECM		Continuity
       Connector	Terminal	Connector	Terminal
       B41	1	E10	96	Existed

    4. Also check harness for short to ground and short to power.

       Is the inspection result normal? 

       YES >> GO TO  12.

       NO >> GO TO 11.

11. DETECT MALFUNCTIONING PART

    Check the following.

    • Harness connectors B10, E29
    • Harness for open or short between EVAP control system pressure sensor and ECM

      Repair open circuit, short to ground or short to power in harness or connectors.

12. CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
    1. Check the continuity between EVAP control system pressure sensor harness connector and ECM harness connector.
       CONTINUITY CHART
       
       

       EVAP control system pressure sensor		ECM		Continuity
       Connector	Terminal	Connector	Terminal
       B41	2	E10	86	Existed

    2. Also check harness for short to ground and short to power.

       Is the inspection result normal? 

       YES >> GO TO  14.

       NO >> GO TO 13.

13. DETECT MALFUNCTIONING PART

    Check the following.

    • Harness connectors B10, E29
    • Harness for open or short between EVAP control system pressure sensor and ECM

      Repair open circuit, short to ground or short to power in harness or connectors.

14. CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR

    Refer to "COMPONENT INSPECTION ".

    Is the inspection result normal? 

    YES >> GO TO 15.

    NO >> Replace EVAP control system pressure sensor.

15. CHECK INTERMITTENT INCIDENT

    Refer to "INTERMITTENT INCIDENT ".

    INSPECTION END