LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2011 >> Versa Base, Automatic >> Repair and Diagnosis >> Body & Frame >> Windows >> Glass & Window System >> Service Information >> Power Window System >> Encoder Circuit Inspection
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Encoder Circuit Inspection

  1. CHECK FRONT POWER WINDOW MOTOR LH POWER SUPPLY
    1. Turn ignition switch OFF.
    2. Disconnect front power window motor LH.
    3. Turn ignition switch ON.
    4. Check voltage between front power window motor LH connector D9 terminal 1 and ground.

      1 - Ground : Approx. 10V 

      OK or NG 

      OK: GO TO  3.

      NG: GO TO 2.

      Fig 1: Checking Voltage Between Front Power Window Motor LH Connector D9 Terminal 1 And Ground
      G06546988Courtesy of NISSAN MOTOR CO., U.S.A.
  2. CHECK HARNESS CONTINUITY
    1. Turn ignition switch OFF.
    2. Disconnect main power window and door lock/unlock switch.
    3. Check continuity between front power window motor LH connector and main power window and door lock/unlock switch connector.
      CONTINUITY SPECIFICATION

      Connector Terminal Connector Terminal Continuity
      A B
      Main power window and door lock/unlock switch: D7 15 Front power window motor LH: D9 1 Yes
      Fig 2: Checking Continuity Between Front Power Window Motor LH And Main Power Window And Door Lock/Unlock Switch Connector
      G06546989Courtesy of NISSAN MOTOR CO., U.S.A.
    4. Check continuity between front power window motor LH connector and ground.
      CONTINUITY SPECIFICATION

      Connector Terminal Ground Continuity
      B
      Front power window motor LH: D9 15 No

      OK or NG 

      OK: Replace main power window and door lock/unlock switch. Refer to "REMOVAL AND INSTALLATION ".

      NG: Repair or replace harness.

  3. CHECK ENCODER GROUND
    1. Turn ignition switch OFF.
    2. Check continuity between front power window motor LH connector D9 terminal 6 and ground.

      6 - Ground : Continuity should exist  .

      OK or NG 

      OK: GO TO  5.

      NG: GO TO 4.

      Fig 3: Checking Continuity Between Front Power Window Motor LH Connector D9 Terminal 6 And Ground
      G04902751Courtesy of NISSAN MOTOR CO., U.S.A.
  4. CHECK ENCODER GROUND CIRCUIT
    1. Disconnect main power window and door lock/unlock switch.
    2. Check continuity between front power window motor LH connector D9 terminal 6 and main power window and door lock/unlock switch connector D7 terminal 2.

      6 - 2 : Continuity should exist  .

      OK or NG 

      OK: Replace main power window and door lock/unlock switch. Refer to "REMOVAL AND INSTALLATION ".

      NG: Repair or replace harness.

      Fig 4: Checking Continuity Between Front Power Window Motor LH And Main Power Window And Door Lock/Unlock Switch
      G04907468Courtesy of NISSAN MOTOR CO., U.S.A.
  5. CHECK ENCODER PULSE A SIGNAL
    1. Connect front power window motor LH.
    2. Turn ignition switch ON.
    3. Check the signal between main power window and door lock/unlock switch connector and ground with oscilloscope.
      SIGNAL SPECIFICATION

      Connector Terminals Condition Signal
      (+) (-)
      D7 13 Ground Opening
      G04877356Courtesy of NISSAN MOTOR CO., U.S.A.
      Fig 5: Checking Signal Between Main Power Window And Door Lock/Unlock Switch Connector And Ground
      G04902764Courtesy of NISSAN MOTOR CO., U.S.A.

      OK or NG 

      OK: Replace main power window and door lock/unlock switch. Refer to "REMOVAL AND INSTALLATION ".

      NG: GO TO 6.

  6. CHECK ENCODER PULSE B SIGNAL

    Check the signal between main power window and door lock/unlock switch connector and ground with oscilloscope.

    SIGNAL SPECIFICATION

    Connector Terminals Condition Signal
    (+) (-)
    D7 9 Ground Opening
    G04877356Courtesy of NISSAN MOTOR CO., U.S.A.
    Fig 6: Checking Signal Between Main Power Window And Door Lock/Unlock Switch Connector And Ground
    G06546995Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: Replace main power window and door lock/unlock switch. Refer to "REMOVAL AND INSTALLATION ".

    NG: GO TO 7.

  7. CHECK ENCODER CIRCUIT
    1. Turn ignition switch OFF.
    2. Disconnect front power window motor LH and main power window and door lock/unlock switch.
    3. Check continuity between front power window motor LH connector and main power window and door lock/unlock switch connector.
      CONTINUITY SPECIFICATION

      Connector Terminal Connector Terminal Continuity
      A B
      Main power window and door lock/unlock switch: D7 9 Front power window motor LH: D9 5 Yes
      13 4
      Fig 7: Checking Continuity Between Front Power Window Motor LH Connector And Ground
      G06546996Courtesy of NISSAN MOTOR CO., U.S.A.
    4. Check continuity between front power window motor LH connector and ground.
      CONTINUITY SPECIFICATION

      Connector Terminal Ground Continuity
      A
      Main power window and door lock/unlock switch: D7 9 No
      13

      OK or NG 

      OK: Replace front power window motor LH. Refer to FRONT DOOR GLASS AND REGULATOR .

      NG: Repair or replace harness.

scientia non olet · About LEMON Manuals