LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2011 >> Versa Base, Standard >> Repair and Diagnosis (Single Page) >> Engine Performance >> Testing & Diagnosis >> Engine Control System - Introduction (Hr16DE) >> Function Diagnosis >> On Board Diagnostic (OBD) System >> CONSULT-III Function >> Data Monitor Mode
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data Monitor Mode

Monitored Item

MONITORED ITEM REFERENCE CHART

Monitored item Unit Description Remarks
ENG SPEED RPM
  • Indicates the engine speed computed from the signal of the crankshaft position sensor (POS) and camshaft position sensor (PHASE).
  • Accuracy becomes poor if engine speed drops below the idle RPM.
  • If the signal is interrupted while the engine is running, an abnormal value may be indicated.
MAS A/F SE-B1 V
  • The signal voltage of the mass air flow sensor is displayed.
  • When the engine is stopped, a certain value is indicated.
  • When engine is running specification range is indicated in "SPEC".
B/FUEL SCHDL ms
  • "Base fuel schedule" indicates the fuel injection pulse width programmed into ECM, prior to any learned on board correction.
  • When engine is running specification range is indicated in "SPEC".
A/F ALPHA-B1 %
  • The mean value of the air-fuel ratio feedback correction factor per cycle is indicated.
  • When the engine is stopped, a certain value is indicated.
  • This data also includes the data for the air-fuel ratio learning control.
  • When engine is running specification range is indicated in "SPEC".
COOLAN TEMP/S °C or °F
  • The engine coolant temperature (determined by the signal voltage of the engine coolant temperature sensor) is displayed.
  • When the engine coolant temperature sensor is open or short-circuited, ECM enters fail-safe mode. The engine coolant temperature determined by the ECM is displayed.
A/F SEN1 (B1) V
  • The A/F signal computed from the input signal of the air fuel ratio (A/F) sensor 1 is displayed.
  
HO2S2 (B1) V
  • The signal voltage of the heated oxygen sensor 2 is displayed.
  
HO2S2 MNTR(B1) RICH/LEAN
  • Display of heated oxygen sensor 2 signal:

RICH: means the amount of oxygen after three way catalyst is relatively small.
LEAN: means the amount of oxygen after three way catalyst is relatively large.
  • When the engine is stopped, a certain value is indicated.
VHCL SPEED SE km/h or mph
  • The vehicle speed computed from the vehicle speed signal sent from combination meter is displayed.
  
BATTERY VOLT V
  • The power supply voltage of ECM is displayed.
  
ACCEL SEN 1 V
  • The accelerator pedal position sensor signal voltage is displayed.
  • ACCEL SEN 2 signal is converted by ECM internally. Thus, it differs from ECM terminal voltage signal.
ACCEL SEN 2
TP SEN 1-B1 V
  • The throttle position sensor signal voltage is displayed.
  • TP SEN 2-B1 signal is converted by ECM internally. Thus, it differs from ECM terminal voltage signal.
TP SEN 2-B1      
FUEL T/TMP SE °C or °F
  • The fuel temperature (determined by the signal voltage of the fuel tank temperature sensor) is displayed.
  
INT/A TEMP SE °C or °F
  • The intake air temperature (determined by the signal voltage of the intake air temperature sensor) is indicated.
  
EVAP SYS PRES V
  • The signal voltage of EVAP control system pressure sensor is displayed.
  
FUEL LEVEL SE V
  • The signal voltage of the fuel level sensor is displayed.
  
START SIGNAL ON/OFF
  • Indicates start signal status [ON/OFF] computed by the ECM according to the signals of engine speed and battery voltage.
  • After starting the engine, [OFF] is displayed regardless of the starter signal.
CLSD THL POS ON/OFF
  • Indicates idle position [ON/OFF] computed by ECM according to the accelerator pedal position sensor signal.
  
AIR COND SIG ON/OFF
  • Indicates [ON/OFF] condition of the air conditioner switch determined by the air conditioner ON signal.
  
P/N POSI SW ON/OFF
  • Indicates [ON/OFF] condition from the park/neutral position (PNP) signal.
  
PW/ST SIGNAL ON/OFF
  • [ON/OFF] condition of the power steering system (determined by the signal sent from EPS control unit) is indicated.
  
LOAD SIGNAL ON/OFF
  • Indicates [ON/OFF] condition from the electrical load signal.

ON: Rear window defogger switch is ON and/or lighting switch is in 2nd position.
OFF: Both rear window defogger switch and lighting switch are OFF.		  
IGNITION SW ON/OFF
  • Indicates [ON/OFF] condition from ignition switch signal.
  
HEATER FAN SW ON/OFF
  • Indicates [ON/OFF] condition from the heater fan switch signal.
  
BRAKE SW ON/OFF
  • Indicates [ON/OFF] condition from the stop lamp switch signal.
  
INJ PULSE-B1 msec
  • Indicates the actual fuel injection pulse width compensated by ECM according to the input signals.
  • When the engine is stopped, a certain computed value is indicated.
IGN TIMING BTDC
  • Indicates the ignition timing computed by ECM according to the input signals.
  • When the engine is stopped, a certain value is indicated.
CAL/LD VALUE %
  • "Calculated load value" indicates the value of the current air flow divided by peak air flow.
  
MASS AIRFLOW g.m/s
  • Indicates the mass air flow computed by ECM according to the signal voltage of the mass air flow sensor.
  
PURG VOL C/V %
  • Indicates the EVAP canister purge volume control solenoid valve control value computed by the ECM according to the input signals.
  • The opening becomes larger as the value increases.
  
INT/V TIM(B1) °CA
  • Indicates [°CA] of intake camshaft advance angle.
  
INT/V SOL(B1) %
  • The control value of the intake valve timing control solenoid valve (determined by ECM according to the input signals) is indicated.
  • The advance angle becomes larger as the value increases.
  
AIR COND RLY ON/OFF
  • The air conditioner relay control condition (determined by ECM according to the input signals) is indicated.
  
FUEL PUMP RLY ON/OFF
  • Indicates the fuel pump relay control condition determined by ECM according to the input signals.
  
VENT CONT/V ON/OFF
  • The control condition of the EVAP canister vent control valve (determined by ECM according to the input signals) is indicated.

ON: Closed
OFF: Open		  
THRTL RELAY ON/OFF
  • Indicates the throttle control motor relay control condition determined by the ECM according to the input signals.
  
COOLING FAN HI/LOW/OFF
  • Indicates the condition of the cooling fan (determined by ECM according to the input signals).

HI: High speed operation
LOW: Low speed operation
OFF: Stop		  
HO2S2 HTR (B1) ON/OFF
  • Indicates [ON/OFF] condition of heated oxygen sensor 2 heater determined by ECM according to the input signals.
  
I/P PULLY SPD RPM
  • Indicates the engine speed computed from the primary sped sensor signal.
  
VEHICLE SPEED km/h or mph
  • The vehicle speed computed from the vehicle speed signal sent from TCM is displayed.
  
IDL A/V LEARN YET/CMPLT
  • Display the condition of Idle Air Volume Learning

YET: Idle air volume learning has not been performed yet.
CMPLT: Idle air volume learning has already been performed successfully.		  
TRVL AFTER MIL km or mile
  • Distance traveled while MIL is activated.
  
A/F S1 HTR(B1) %
  • Air fuel ratio (A/F) sensor 1 heater control value computed by ECM according to the input signals.
  • The current flow to the heater becomes larger as the value increases.
  
AC PRESS SEN V
  • The signal voltage from the refrigerant pressure sensor is displayed.
  
A/F ADJ-B1 -
  • Indicates the correction of factor stored in ECM. The factor is calculated from the difference between the target air-fuel ratio stored in ECM and the air-fuel ratio calculated from A/F sensor 1 signal.
  
HO2 S2 DIAG2 (B1)(1) [INCMP/CMPLT] -
  • Indicates DTC P0139 self-diagnosis (slow responce)

INCMP: Self-diagnosis is incomplete.
CMPLT: Self-diagnosis is complete.		  
(1) The item is indicated, but not used.
NOTE: Any monitored item that does not match the vehicle being diagnosed is deleted from the display automatically.
scientia non olet · About LEMON Manuals