Common Specifications & Procedures
CUBE COMMON SPECIFICATIONS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Torque | See Torque Specifications in applicable figures under REMOVAL AND INSTALLATION . | ||
| Axle Nut/Hub Nut | |||
| Front Axle Nut/Hub Bearing Bolts | Axle Nut: 125 N.m (92 Ft. lbs.) Hub Bearing Bolts: 88.3 N.m (65 Ft. lbs) |
||
| Battery | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING BRAKE SYSTEM | ||
| Disc Brakes (Front) | FRONT DISC BRAKE | ||
| Drum Brakes (Rear) | REAR DRUM BRAKE | ||
| Torque | |||
| Front | See Torque Specifications in applicable figures under FRONT DISC BRAKE . | ||
| Rear | See Torque Specifications in applicable figures under REAR DRUM BRAKE . | ||
| Charging | |||
| Alternator | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Torque | See Torque Specifications in applicable figures under REMOVAL AND INSTALLATION . | ||
| Drive Belts | |||
| Adjustment | Belt tension is automatically adjusted by drive belt auto-tensioner. | ||
| Belt Routing | DRIVE BELT | ||
| Engine Cooling | |||
| General Service Specifications | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Radiator Cap Pressure | 11-14 psi (78-98 kPa, 0.8-1.0 kgf/cm2 ) | ||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | COMPRESSION PRESSURE | ||
| Oil Pressure @ Engine oil temperature of 176°F (80°C) | |||
| @ Idle | 9 psi (60 kPa.061 kgf/cm2 ) | ||
| @ 2000 RPM | 29 psi (200 kPa, 2.0 kgf/cm2 ) | ||
| Overhaul | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Torque | See Torque Specifications in applicable figures under UNIT DISASSEMBLY AND ASSEMBLY | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint" button. | ||
| Flywheel/Flex Plate (Drive Plate) Torque | 80 Ft. lbs. (108 N.m) | ||
| Fuel System | |||
| Fuel Pressure Release Procedure | |||
| For California | FUEL PRESSURE RELEASE | ||
| Except California | FUEL PRESSURE RELEASE | ||
| Pressure Specification | At Idling: Approximately 51 psi (350 kPa, 3.57 kg/cm2 ) | ||
| Fuel Pressure Test Procedure | |||
| For California | FUEL PRESSURE CHECK | ||
| Except California | FUEL PRESSURE CHECK | ||
| Fuel Filter Location | Fuel filter is attached to fuel Pump Unit located in fuel tank. | ||
| Fuel Filter R & I | FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Engine is equipped with Coil On Plug ignition. | ||
| Ignition Wires (Routing) | Engine is equipped with Coil On Plug ignition. | ||
| Spark Plugs | SPARK PLUG Tightening torque: 14 ft. Lbs. (19.6 N.m) |
||
| Starting | |||
| Starter | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Torque | See Torque Specifications in applicable figures under STARTER MOTOR . | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Front | WHEEL ALIGNMENT | ||
| Rear | WHEEL ALIGNMENT | ||
| Torque | |||
| Front | See Torque Specifications in applicable figures under REMOVAL AND INSTALLATION . | ||
| Rear | See Torque Specifications in applicable figures under REMOVAL AND INSTALLATION . | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 80 Ft. lbs (108 N.m, 11 kg. m) | ||
| How To Use Nissan Service Information | |||
| Includes: Standard Bolt Torque Symbol Identification General Connector Info |
GENERAL INFORMATION | ||