Values On The Diagnosis Tool

Remarks:

Specification data are reference values.
Specification data are output/input values which are detected or supplied by the ECM at the connector.

*Specification data may not be directly related to their components signals/values/operations.

I.e. Adjust ignition timing with a timing light before monitoring IGN TIMING, because the monitor may show the specification data in spite of the ignition timing not being adjusted to the specification data. this IGN TIMING monitors the data calculated by the ECM according to the signals input from the camshaft position sensor and other ignition timing related sensors.

Monitor Item

Condition

Values/Status

ENG SPEED

Run engine and compare CONSULT value with the tachometer indication.

Almost the same speed as the tachometer indication.

MAS A/F SE-B1

See "DIAGNOSIS PROCEDURE ".

B/FUEL SCHDL

See "DIAGNOSIS PROCEDURE ".

A/F ALPHA-B1

See "DIAGNOSIS PROCEDURE ".

COOLAN TEMP/S

Engine: After warming up

More than 70°C (158F)

A/F SEN1 (B1)

Engine: After warming up

Maintaining engine speed at 2, 000 rpm

Fluctuates around 2.2 V

HO2S2 (B1)

Revving engine from idle up to 3, 000 rpm quickly after the following conditions are met.
- Engine: After warming up
- After keeping engine speed between 3, 500 and 4, 000 rpm for 1 minute and at idle for 1 minute under no load

0 - 0.3 V ←→ Approx. 0.6 - 1.0 V

HO2S2 MNTR (B1)

LEAN ←→ RICH

VHCL SPEED SE

Turn drive wheels and compare CONSULT value with the speedometer indication.

Almost the same speed as speedometer indication

BATTERY VOLT

Ignition switch: ON (Engine stopped)

11 - 14 V

ACCEL SEN 1

Ignition switch: ON (Engine stopped)

Accelerator pedal: Fully released

0.6 - 0.9 V

Accelerator pedal: Fully depressed

4.0 - 4.8 V

ACCEL SEN 2⁽¹⁾

Ignition switch: ON (Engine stopped)

Accelerator pedal: Fully released

0.6 - 0.9 V

Accelerator pedal: Fully depressed

3.9 - 4.8 V

TP SEN 1-B1

Ignition switch: ON (Engine stopped)
Selector lever position: D (CVT) or 1st (M/T)

Accelerator pedal: Fully released

More than 0.36 V

Accelerator pedal: Fully depressed

Less than 4.75 V

TP SEN 2-B1⁽¹⁾

Ignition switch: ON (Engine stopped)
Selector lever position: D (CVT) or 1st (M/T)

Accelerator pedal: Fully released

More than 0.36 V

Accelerator pedal: Fully depressed

Less than 4.75 V

START SIGNAL

Ignition switch: ON → START → ON

OFF → ON → OFF

CLSD THL POS

Ignition switch: ON (Engine stopped)

Accelerator pedal: Fully released

Accelerator pedal: Slightly depressed

OFF

AIR COND SIG

Engine: After warming up, idle the engine

Air conditioner switch: OFF

OFF

Air conditioner switch: ON (Compressor operates.)

P/N POSI SW

Ignition switch: ON

Selector lever position: P or N (CVT) or Neutral (M/T)

Selector lever position: Except above

OFF

PW/ST SIGNAL

Engine: After warming up, idle the engine

Steering wheel: Not being turned

OFF

Steering wheel: Being turned

LOAD SIGNAL

Ignition switch: ON

Rear window defogger switch: ON and/or Lighting switch: 2nd position

Rear window defogger switch and lighting switch: OFF

OFF

IGNITION SW

Ignition switch: ON → OFF → ON

ON → OFF → ON

HEATER FAN SW

Engine: After warming up, idle the engine

Heater fan switch: ON

Heater fan switch: OFF

OFF

BRAKE SW

Ignition switch: ON

Brake pedal: Fully released

OFF

Brake pedal: Slightly depressed

INJ PULSE-B1

Engine: After warming up
Selector lever position: P or N (CVT) or Neutral (M/T)
Air conditioner switch: OFF
No load

Idle

2.0 - 3.0 msec

2, 000 rpm

1.9 - 2.9 msec

IGN TIMING

Engine: After warming up
Selector lever position: P or N (CVT) or Neutral (M/T)
Air conditioner switch: OFF
No load

Idle

8 - 18°BTDC

2, 000 rpm

25 - 45°BTDC

CAL/LD VALUE

Engine: After warming up
Selector lever position: P or N (CVT) or Neutral (M/T)
Air conditioner switch: OFF
No load

Idle

10 - 35%

2, 500 rpm

10 - 35%

MASS AIRFLOW

Engine: After warming up
Selector lever position: P or N (CVT) or Neutral (M/T)
Air conditioner switch: OFF
No load

Idle

1.0 - 4.0 g/s

2, 500 rpm

2.0 - 10.0 g/s

PURG VOL C/V

Engine: After warming up
Selector lever position: P or N (CVT) or Neutral (M/T)
Air conditioner switch: OFF
No load

Idle

2, 000 rpm

0 - 50%

INT/V TIM (B1)

Engine: After warming up
Selector lever position: P or N (CVT) or Neutral (M/T)
Air conditioner switch: OFF
No load

Idle

-5 - 5°CA

2, 000 rpm

Approx. 0 - 40°CA

INT/V SOL (B1)

Engine: After warming up
Selector lever position: P or N (CVT) or Neutral (M/T)
Air conditioner switch: OFF
No load

Idle

0 - 2%

2, 000 rpm

Approx. 0 - 90%

SWRL CONT S/V

Ignition switch: ON
Engine coolant temperature: Between 5°C (41°F) and 40°C (104°F)

Accelerator pedal: Fully released

Accelerator pedal: Slightly depressed

OFF

TMBL POS SEN

Ignition switch: ON
Engine coolant temperature: Between 5°C (41°F) and 60°C (140°F)

Accelerator pedal: Fully released

Less than 1.2 V

Accelerator pedal: Slightly depressed

More than 2.9 V

AIR COND RLY

Engine: After warming up, idle the engine

Air conditioner switch: OFF

OFF

Air conditioner switch: ON (Compressor operates)

FUEL PUMP RLY

For 1 second after turning ignition switch: ON
Engine running or cranking

Except above

OFF

THRTL RELAY

Ignition switch: ON

COOLING FAN

Engine: After warning up, idle the engine
Air conditioner switch: OFF

Engine coolant temperature is 98°C (208°F) or less

OFF

Engine coolant temperature is between 98°C (208°F) and 99°C (210°F)

LOW

Engine coolant temperature is 100°C (212°F) or more

HIGH

HO2S2 HTR (B1)

Engine speed: Below 3, 600 rpm after the following conditions are met.
- Engine: After warming up
- Keeping the engine speed between 3, 500 and 4, 000 rpm for 1 minute and at idle for 1 minute under no load

VEHICLE SPEED

Turn drive wheels and compare CONSULT value with the speedometer indication.

Almost the same speed as the speedometer indication

IDL A/V LEARN

Engine: running

Idle air volume learning has not been performed yet.

YET

Idle air volume learning has already been performed successfully.

CMPLT

TRVL AFTER MIL

Ignition switch: ON

Vehicle has traveled after MIL has turned ON.

0 - 65, 535 km (0 - 40, 723 miles)

ENG OIL TEMP

Engine: After warming up

More than 70°C (158F)

A/F S1 HTR (B1)

Engine: After warming up, idle the engine (More than 140 seconds after starting engine)

4 - 100%

AC PRESS SEN

Engine: Idle
Both A/C switch and blower fan switch: ON (Compressor operates)

1.0 - 4.0 V

EVAP SYS PRES

Ignition switch: ON

Approx 1.8 - 4.8 V

VENT CONT/V

Ignition switch: ON

OFF

I/P PULLY SPD

Vehicle speed: More than 20 km/h (12MPH)

Almost the same speed as the tachometer indication.

A/F ADJ-B1

Engine: Running

-0.330 - 0.330

FUEL T/TMP SE

Ignition switch: ON

Indicates fuel tank temperature.

INT/A TEMP SE

Ignition switch: ON

Indicates intake air temperature.

FUEL LEVEL SE

Ignition switch: ON

Depending on fuel level of fuel tank.

BAT CUR SEN

Engine speed: Idle
Battery: Fuel charged⁽²⁾
Selector lever: P or N (CVT), Neutral (M/T)
Air conditioner switch: OFF
No load

Approx 2, 600 - 3, 500 mV

ALT DUTY

Engine: Idle

0 - 80%

ALT DUTY SIG

Power generation voltage variable control: Operating

Power generation voltage variable control: Not operating

OFF

VHCL SPEED SE

Turn drive wheels and compare CONSULT value with the speedometer indication.

Almost the same speed as the speedometer indication.

SET VHCL SPD

Engine: Running

ASCD: Operating

The preset vehicle speed is displayed.

MAIN SW

Ignition switch: ON

MAIN switch: pressed

MAIN switch: Released

OFF

CANCEL SW

Ignition switch: ON

CANCEL switch: pressed

CANCEL switch: Released

OFF

SET SW

Ignition switch: ON

SET/COAST switch: pressed

SET/COAST switch: Released

OFF

RESUME/ACC SW

Ignition switch: ON

RESUME/ACCELERATE switch: pressed

RESUME/ACCELERATE switch: Released

OFF

BRAKE SW1 (ASCD brake switch)

Ignition switch: ON

Brake pedal: Fully released (CVT)
Brake pedal and clutch pedal: Fully released (M/T)

Brake pedal: Slightly depressed (CVT)
Brake pedal and/or clutch pedal: Slightly depressed (M/T)

OFF

BRAKE SW2 (stop lamp switch)

Ignition switch: ON

Brake pedal: Fully released

OFF

Brake pedal: Slightly depressed

VHCL SPD CUT

Ignition switch: ON

NON

LO SPEED CUT

Ignition switch: ON

NON

AT OD MONITOR

Ignition switch: ON

OFF

AT OD CANCEL

Ignition switch: ON

OFF

CRUISE LAMP

Ignition switch: ON

MAIN switch: Pressed at the 1st time → at the 2nd time

ON → OFF

SET LAMP

MAIN switch: ON
Vehicle speed: Between 40 km/h (25 MPH) and 144 km/h (89 MPH)

ASCD: Operating

ASCD: Not operating

OFF

THRTL STK CNT B1

NOTE: The item is indicated, but not used.

EVAP LEAK DIAG

Ignition switch: ON

Indicates the condition of EVAP leak diagnosis.

EVAP DIAG READY

Ignition switch: ON

Indicates the ready condition of EVAP leak diagnosis.

HO2 S2 DIAG1 (B1)

DTC P0139 self-diagnosis (delayed response) is incomplete.

INCMP

DTC P0139 self-diagnosis (delayed response) is complete.

CMPLT

HO2 S2 DIAG2 (B1)

DTC P0139 self-diagnosis (slow response) is incomplete.

INCMP

DTC P0139 self-diagnosis (slow response) is complete.

CMPLT

A/F SEN1 DIAG2 (B1)

DTC P014C and P014D self-diagnosis is incomplete.

INCMP

DTC P014C and P014D self-diagnosis is complete.

CMPLT

A/F SEN1 DIAG3 (B1)

The vehicle condition is not within the diagnosis range of DTC P014C, P014D, P015A or P015B.

ABSNT

The vehicle condition is within the diagnosis range of DTC P014C, P014D, P015A or P015B.

PRSNT

SYSTEM 1 DIAGNOSIS A B1

DTC P117A self-diagnosis is incomplete.

INCMP

DTC P117A self-diagnosis is complete.

CMPLT

SYSTEM 1 DIAGNOSIS B B1

DTC P117A self-diagnosis is on standby.

ABSENT

DTC P117A self-diagnosis is under diagnosis.

PRSENT

⁽¹⁾	Accelerator pedal position sensor 2 signal and throttle position sensor 2 signal are converted by ECM internally. Thus, they differ from ECM terminals voltage signal.

⁽²⁾	Before measuring the terminal voltage, confirm that the battery is fully charged. Refer to "HOW TO HANDLE BATTERY ".