Data Monitor
Operation Procedure
- Connect "CONSULT."
- Touch "DATA MONITOR".
- Select from "SELECT MONITOR ITEM", screen of data monitor mode is displayed.
NOTE:
When malfunction is detected, CONSULT performs REAL-TIME DIAGNOSIS.
Also, any malfunction detected while in this mode will be displayed at real time.
Also, any malfunction detected while in this mode will be displayed at real time.
| x: Standard -: Not applicable | ||||
|---|---|---|---|---|
| Monitor Item (Unit) | Selection | Description | ||
| ECU INPUT SIGNALS | MAIN SIGNALS | SELECTION FROM MENU | ||
| VHCL/S SEN.FR [km/h] or [mph] | x | - | x | Wheel speed calculated by ABS actuator and electric unit (control unit). Signal input with CAN communication line. |
| VHCL/S SEN.RR [km/h] or [mph] | x | - | x | Wheel speed calculated by TCM. Signal input with CAN communication line. |
| ENGINE SPEED [rpm] | x | - | x | Engine speed is displayed. Signal input with CAN communication line. |
| BATTERY VOLT [V] | x | - | x | Power supply voltage for transfer control unit. |
| 2WD SWITCH [On/Off] | x | - | x | 4WD shift switch signal status is displayed. (4L means 4LO of 4WD shift switch.) |
| 4H SWITCH [On/Off] | x | - | x | |
| 4L SWITCH [On/Off] | x | - | x | |
| 4L POSI SW [On/Off] | x | - | x | 4LO switch signal status is displayed. |
| ATP SWITCH [On/Off] | x | - | x | ATP switch signal status is displayed. |
| WAIT DETCT SW [On/Off] | x | - | x | Wait detection switch signal status is displayed. |
| 4WD MODE [2H/4H/4L] | - | x | x | Control status of 4WD recognized by transfer control unit. (2WD, 4H or 4LO) |
| VHCL/S COMP [km/h] or [mph] | - | x | x | Vehicle speed recognized by transfer control unit. |
| SHIFT ACT 1 [On/Off] | - | x | x | Output condition to actuator motor (clockwise) |
| SHIFT AC MON1 [On/Off] | - | - | x | Check signal for transfer control unit signal output |
| SHIFT ACT 2 [On/Off] | - | x | x | Output condition to actuator motor (counterclockwise) |
| SHIFT AC MON2 [On/Off] | - | - | x | Check signal for transfer control unit signal output |
| SFT ACT/R MON [On/Off] | - | - | x | Operating condition of actuator motor relay (integrated in transfer control unit) |
| SHIFT POS SW1 [On/Off] | x | - | x | Condition of actuator position switch 1 |
| SHIFT POS SW2 [On/Off] | x | - | x | Condition of actuator position switch 2 |
| SHIFT POS SW3 [On/Off] | x | - | x | Condition of actuator position switch 3 |
| SHIFT POS SW4 [On/Off] | x | - | x | Condition of actuator position switch 4 |
| 4WD FAIL LAMP [On/Off] | - | x | x | Control status of 4WD warning lamp is displayed. |
| 2WD IND [On/Off] | - | - | x | Control status of 4WD shift indicator lamp (rear) is displayed. |
| 4H IND [On/Off] | - | - | x | Control status of 4WD shift indicator lamp (front and center) is displayed. |
| 4L IND [On/Off] | - | - | x | Control status of 4LO indicator lamp is displayed. |