LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2012 >> Quest SV >> Repair and Diagnosis >> External Pages >> Different car >> Section 53 (Engine Control System - Introduction) >> System Description >> Diagnosis System (ECM) >> Diagnosis Description >> CONSULT Function >> Active Test Mode
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Active Test Mode

WARNING: This page is about a different car, the 2011 Nissan Quest. However, it is still accessible from the selected car via links, so may be relevant.

Test Item

ACTIVE TEST MODE REFERENCE CHART

TEST ITEM CONDITION JUDGMENT CHECK ITEM (REMEDY)
FUEL INJECTION
  • Engine: Return to the original non-standard condition
  • Change the amount of fuel injection using CONSULT.
 If malfunctioning symptom disappears, see the appropriate CHECK ITEM.
  • Harness and connectors
  • Fuel injector
  • Air fuel ratio (A/F) sensor 1
IGNITION TIMING
  • Engine: Return to the original non-standard condition
  • Timing light: Set
  • Retard the ignition timing using CONSULT.
 If malfunctioning symptom disappears, see the appropriate CHECK ITEM.
  • Perform Idle Air Volume Learning.
POWER BALANCE
  • Engine: After warming up, idle the engine.
  • A/C switch OFF
  • Selector lever: P or N position
  • Cut off each injector signal one at a time using CONSULT.
 Engine runs rough or stops.
  • Harness and connectors
  • Compression
  • Fuel injector
  • Power transistor
  • Spark plug
  • Ignition coil
COOLING FAN(1)
  • Ignition switch: ON
  • Turn the cooling fan "HI", "MID", "LOW" and "OFF" using CONSULT.
 Cooling fan moves and stops.
  • Harness and connectors
  • Cooling fan motor
  • IPDM E/R
ENG COOLANT TEMP
  • Engine: Return to the original non-standard condition
  • Change the engine coolant temperature using CONSULT.
 If malfunctioning symptom disappears, see the appropriate CHECK ITEM.
  • Harness and connectors
  • Engine coolant temperature sensor
  • Fuel injector
FUEL PUMP RELAY
  • Ignition switch: ON (Engine stopped)
  • Turn the fuel pump relay "ON" and "OFF" using CONSULT and listen to operating sound.
 Fuel pump relay makes the operating sound.
  • Harness and connectors
  • Fuel pump relay
VIAS S/V-1
  • Ignition switch: ON
  • Turn solenoid valve "ON" and "OFF" using CONSULT and listen to operating sound.
 Solenoid valve makes the operating sound.
  • Harness and connectors
  • Solenoid valve
VIAS S/V-2
  • Ignition switch: ON
  • Turn solenoid valve "ON" and "OFF" using CONSULT and listen to operating sound.
 Solenoid valve makes the operating sound.
  • Harness and connectors
  • Solenoid valve
ENGINE MOUNTING
  • Ignition switch: ON
  • Turn electronic controlled engine mount "IDLE" and "TRVL" with CONSULT.
 Electronic controlled engine mount makes the operating sound.
  • Harness and connectors
  • Electronic controlled engine mount
PURG VOL CONT/V
  • Engine: After warming up, run engine at 1, 500 RPM.
  • Change the EVAP canister purge volume control solenoid valve opening percent using CONSULT.
 Engine speed changes according to the opening percent.
  • Harness and connectors
  • Solenoid valve
FUEL/T TEMP SEN
  • Change the fuel tank temperature using CONSULT.
VENT CONTROL/V
  • Ignition switch: ON (Engine stopped)
  • Turn solenoid valve "ON" and "OFF" with the CONSULT and listen to operating sound.
 Solenoid valve makes an operating sound.
  • Harness and connectors
  • Solenoid valve
INT V/T ASSIGN ANGLE
  • Engine: Return to the original non-standard condition
  • Change intake valve timing using CONSULT.
 If malfunctioning symptom disappears, see the appropriate CHECK ITEM.
  • Harness and connectors
  • Intake valve timing control solenoid valve
ALTERNATOR DUTY
  • Engine: Idle
  • Change duty ratio using CONSULT.
 Battery voltage changes.
  • Harness and connectors
  • IPDM E/R
  • Alternator
FPCM
  • Engine: Return to the original trouble condition
  • Select "LOW", "MID" and "HI" with CONSULT.
 Fuel pump speed changes or stops.
  • Harness and connectors
  • Fuel pump control module (FPCM)
(1) Leaving cooling fan OFF with CONSULT while engine is running may cause the engine to overheat.
scientia non olet · About LEMON Manuals