LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2012 >> Xterra PRO-4X, Automatic Trans >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System - Component Testing >> Refrigerant Pressure Sensor >> Diagnosis Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Diagnosis Procedure

  1. CHECK REFRIGERANT PRESSURE SENSOR OVERALL FUNCTION
    1. Start engine and warm it up to normal operating temperature.
    2. Turn A/C switch and blower switch ON.
    3. Check voltage between ECM terminal 70 and ground with CONSULT or tester.

    Voltage: 1.0 - 4.0V 

    OK or NG 

    OK: INSPECTION END

    NG: GO TO 2.

    Fig 1: Checking Voltage Between ECM Terminal 70 And Ground
    G04900823Courtesy of NISSAN NORTH AMERICA, INC.
  2. CHECK GROUND CONNECTIONS
    1. Turn A/C switch and blower switch OFF.
    2. Turn ignition switch OFF.
    3. Loosen and retighten three ground screws on the body. Refer to "GROUND INSPECTION ".
    Fig 2: Checking Ground Connections
    G04895412Courtesy of NISSAN NORTH AMERICA, INC.

    OK or NG 

    OK: GO TO 3.

    NG: Repair or replace ground connections.

  3. CHECK REFRIGERANT PRESSURE SENSOR POWER SUPPLY CIRCUIT
    1. Disconnect refrigerant pressure sensor harness connector.
    2. Turn ignition switch ON.
      Fig 3: Identifying Refrigerant Pressure Sensor Harness Connector
      G04897432Courtesy of NISSAN NORTH AMERICA, INC.
    3. Check voltage between refrigerant pressure sensor terminal 3 and ground with CONSULT or tester.

    Voltage: Approximately 5V 

    Fig 4: Checking Voltage Between Refrigerant Pressure Sensor Terminal 3 And Ground
    G04895224Courtesy of NISSAN NORTH AMERICA, INC.

    OK or NG 

    OK: GO TO  5.

    NG: GO TO 4.

  4. DETECT MALFUNCTIONING PART

    Check the following.

    • Harness connectors E5, F14
    • Harness for open or short between ECM and refrigerant pressure sensor

    : Repair harness or connectors.

  5. CHECK REFRIGERANT PRESSURE SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
    1. Turn ignition switch OFF.
    2. Disconnect ECM harness connector.
    3. Check harness continuity between refrigerant pressure sensor terminal 1 and ECM terminal 67.

      Refer to WIRING DIAGRAM Wiring Diagram.

      Continuity should exist. 

    4. Also check harness for short to ground and short to power.

    OK or NG 

    OK: GO TO  7.

    NG: GO TO 6.

  6. DETECT MALFUNCTIONING PART

    Check the following.

    • Harness connectors E5, F14
    • Harness for open or short between ECM and refrigerant pressure sensor

    : Repair open circuit or short to ground or short to power in harness or connectors.

  7. CHECK REFRIGERANT PRESSURE SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
    1. Check harness continuity between ECM terminal 70 and refrigerant pressure sensor terminal 2.

      Refer to WIRING DIAGRAM Wiring Diagram.

      Continuity should exist. 

    2. Also check harness for short to ground and short to power.

    OK or NG 

    OK: GO TO  9.

    NG: GO TO 8.

  8. DETECT MALFUNCTIONING PART

    Check the following.

    • Harness connectors E5, F14
    • Harness for open or short between ECM and refrigerant pressure sensor

    : Repair open circuit or short to ground or short to power in harness or connectors.

  9. CHECK INTERMITTENT INCIDENT

    Refer to "INTERMITTENT INCIDENT ".

    OK or NG 

    OK: Replace refrigerant pressure sensor. Refer to "REMOVAL AND INSTALLATION ".

    NG: Repair or replace.

scientia non olet · About LEMON Manuals