Common Specifications & Procedures
CUBE COMMON SPECIFICATIONS & PROCEDURES
| System | Specification/Procedure | |||
|---|---|---|---|---|
| Air Conditioning | ||||
| Service | SERVICE DATA AND SPECIFICATIONS (SDS) | |||
| Torque | See Torque Specifications in Text and applicable graphics under REMOVAL AND INSTALLATION | |||
| Axle Nut/Hub Nut | ||||
| Front Axle Nut | 92 Ft. lbs. (125 N.m) | |||
| Hub Bearing Bolts | ||||
| Front | 65 Ft. lbs (88.3 N.m) | |||
| Rear | 70 Ft. lbs (94.3 N.m) | |||
| Battery | SERVICE DATA AND SPECIFICATIONS (SDS) | |||
| Brakes | ||||
| Bleeding Sequence | BLEEDING BRAKE SYSTEM | |||
| Disc Brakes (Front) | FRONT DISC BRAKE | |||
| Drum Brakes (Rear) | REAR DRUM BRAKE | |||
| Torque | ||||
| Front | See Torque Specifications in text and applicable figures under FRONT DISC BRAKE | |||
| Rear | See Torque Specifications in text and applicable figures under REAR DRUM BRAKE | |||
| Charging | ||||
| Alternator | SERVICE DATA AND SPECIFICATIONS (SDS) | |||
| Torque | See Torque Specifications in Text and applicable figures under ALTERNATOR . | |||
| Drive Belts | ||||
| Adjustment | Belt tension is automatically adjusted by drive belt auto-tensioner. | |||
| Belt Routing | DRIVE BELT | |||
| Engine Cooling | ||||
| General Service Specifications | SERVICE DATA AND SPECIFICATIONS (SDS) | |||
| Radiator Cap Pressure | 11-14 psi (78-98 kPa, 0.8-1.0 kgf/cm2 ) | |||
| Thermostat R & I | THERMOSTAT | |||
| Water Pump R & I | WATER PUMP | |||
| Engine Mechanical | ||||
| Compression | COMPRESSION PRESSURE | |||
| Oil Pressure @ Engine oil temperature of 176°F (80°C) | ||||
| @ Idle | 9 psi (60 kPa.061 kgf/cm2 ) | |||
| @ 2000 RPM | 29 psi (200 kPa, 2.0 kgf/cm2 ) | |||
| Overhaul | SERVICE DATA AND SPECIFICATIONS (SDS) | |||
| Torque | See Torque Specifications in Text and applicable figures in UNIT DISASSEMBLY AND ASSEMBLY | |||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint" button. | |||
| Flywheel/Flex Plate (Drive Plate) Torque | 80 Ft. lbs (108 N.m) | |||
| Fuel System | ||||
| Fuel Pressure Release Procedure | ||||
| All Engines | FUEL PRESSURE RELEASE | |||
| Pressure Specification | At Idling: Approximately 51 psi (350 kPa, 3.57 kg/cm2 ) | |||
| Fuel Pressure Test Procedure | ||||
| All Engines | FUEL PRESSURE CHECK | |||
| Fuel Filter Location | Fuel filter is attached to fuel Pump Unit located in fuel tank. | |||
| Fuel Filter R & I | FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY | |||
| Ignition | ||||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | |||
| Ignition Wires (Resistance) | Engine is equipped with Coil On Plug ignition. | |||
| Ignition Wires (Routing) | Engine is equipped with Coil On Plug ignition. | |||
| Spark Plugs | SPARK PLUG Tightening torque: 14 ft. Lbs. (19.6 N.m) |
|||
| Starting | ||||
| Starter | SERVICE DATA AND SPECIFICATIONS (SDS) | |||
| Torque | See Torque Specifications in Text and applicable figures under STARTER MOTOR | |||
| Wheel Alignment | ||||
| Adjustment Specifications | ||||
| Front | WHEEL ALIGNMENT | |||
| Rear | WHEEL ALIGNMENT | |||
| Torque | ||||
| Front | See Torque Specifications in Text and applicable graphics under REMOVAL AND INSTALLATION | |||
| Rear | See Torque Specifications in Text and applicable graphics under REMOVAL AND INSTALLATION | |||
| Wheel & Tire | ||||
| Wheel Lug Nut Torque | 80 Ft. lbs (108 N.m) | |||
| How To Use Nissan Service Information | ||||
| Includes: Standard Bolt Torque Symbol Identification General Connector Info |
Refer to GENERAL INFORMATION . | |||