Diagnosis Procedure

Regarding Wiring Diagram information, refer to "WIRING DIAGRAM ".

1. DETECT MALFUNCTIONING ITEMS 

   What is malfunction items? 

   ECO mode switch illumination does not turns ON: GO TO 2.

   ECO mode indicator lamp does not turns ON: GO TO  8.

2. CHECK ECO MODE SWITCH ILLUMINATION POWER SUPPLY (1) 
   1. Turn OFF the headlamp.
   2. Turn ignition switch OFF.
   3. Disconnect ECO mode switch harness connector.
   4. Turn ignition switch ON.
   5. Turn ON the headlamp.
   6. Check the voltage between ECO mode switch harness connector terminals.

      ECO mode switch			Voltage
      Connector	+	-
      	Terminal
      M82	1	4	Battery voltage

      Is the inspection result normal? 

      YES: GO TO 3.

      NO: GO TO  4.

3. CHECK INTERMITTENT INCIDENTE 

   Refer to "INTERMITTENT INCIDENT ".

   Is the inspection result normal? 

   YES: Replace ECO mode switch. Refer to "REMOVAL AND INSTALLATION ".

   NO: Replace the fuse after repair the applicable circuit.

4. CHECK ECO MODE SWITCH ILLUMINATION POWER SUPPLY (2) 

   Check the voltage between ECO mode switch harness connector and ground.

   +		-	Voltage
   ECO mode switch
   Connector	Terminal
   M82	1	Ground	Battery voltage

   Is the inspection result normal? 

   YES: GO TO  7.

   NO: GO TO 5.

5. CHECK FUSE 
   1. Turn OFF the headlamp.
   2. Turn ignition switch OFF.
   3. Pull out #37 fuse. Refer to "TERMINAL ARRANGEMENT ".
   4. Check that the fuse is not fusing.

      Is the inspection result normal? 

      YES: GO TO 6.

      NO: Replace the fuse after repair the applicable circuit.

6. CHECK ECO MODE SWITCH ILLUMINATION POWER SUPPLY CIRCUIT 
   1. Disconnect IPDM E/R harness connector E45. Refer to "WIRING DIAGRAM ".
   2. Check the continuity between IPDM E/R harness connector and ECO mode switch harness connector.

      +		-		Continuity
      IPDM E/R		ECO mode switch
      Connector	Terminal	Connector	Terminal
      E45	33	M82	1	Existed

   3. Also check harness for short to ground.

      Is the inspection result normal? 

      YES: Perform IPDM E/R auto active test and check tail lamp relay operation. Refer to "DIAGNOSIS DESCRIPTION " (with intelligent key), "DIAGNOSIS DESCRIPTION " (without intelligent key).

      NO: Repair or replace error-detected parts.

7. CHECK GROUND CIRCUIT 
   1. Turn OFF the headlamp.
   2. Turn ignition switch OFF.
   3. Check continuity between ECO mode switch harness connector terminal and ground.

      +		-	Continuity
      ECO mode switch
      Connector	Terminal
      M82	4	Ground	Existed

      Is the inspection result normal? 

      YES: Check intermittent incident. Refer to "INTERMITTENT INCIDENT ".

      NO: Repair or replace error-detected parts.

8. CHECK ECO MODE SWITCH CIRCUIT 
   1. Turn ignition switch OFF.
   2. Disconnect ECO mode switch harness connector.
   3. Turn ignition switch ON.
   4. Check voltage between ECO mode switch harness connector terminals.

      ECO mode switch			Voltage (Approx.)
      Connector	+	-
      	Terminal
      M82	6	8	5 V

      Is the inspection result normal? 

      YES: GO TO  13.

      NO: GO TO 9.

9. CHECK GROUND CIRCUIT 
   1. Turn ignition switch OFF.
   2. Check the continuity between ECO mode switch harness connector and ground.

      ECO mode switch		-	Continuity
      Connector	Terminal
      M82	8	Ground	Existed

      Is the inspection result normal? 

      YES: GO TO 10.

      NO: Repair or replace damaged parts.

10. CHECK CIRCUIT BETWEEN COMBINATION METER AND ECO MODE SWITCH (1) 
    1. Disconnect combination meter harness connector M24.
    2. Check continuity between combination meter harness connector terminal and ECO mode switch harness connector terminal.

       Combination meter		ECO mode switch		Continuity
       Connector	Terminal	Connector	Terminal
       M24	25	M82	6	Existed

       Is the inspection result normal? 

       YES: GO TO 11.

       NO: Repair or replace damaged parts.

11. CHECK CIRCUIT BETWEEN COMBINATION METER AND ECO MODE SWITCH (2) 

    Check continuity between combination meter harness connector terminal and ECO mode switch harness connector terminal.

    Combination meter		-	Continuity
    Connector	Terminal
    M24	25	Ground	Not existed

    Is the inspection result normal? 

    YES: GO TO 12.

    NO: Repair or replace damaged parts.

12. CHECK COMBINATION METER INPUT/OUTPUT SIGNAL 
    1. Connect all of disconnected connectors.
    2. Check input/output signal of combination meter. Refer to "REFERENCE VALUE ".

       Is the inspection result normal? 

       YES: Check intermittent incident. Refer to "INTERMITTENT INCIDENT ".

       NO: Replace combination meter. Refer to "REMOVAL AND INSTALLATION ".

13. CHECK ECO MODE SWITCH 

    Check ECO mode switch. Refer to "COMPONENT INSPECTION ".

    Is the inspection result normal? 

    YES: Check intermittent incident. Refer to "INTERMITTENT INCIDENT ".

    NO: Replace ECO mode switch. Refer to "REMOVAL AND INSTALLATION ".