LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2015 >> Altima Base >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Infotainment >> Audio, Visual & Navigation System (Navigation Systems) >> Navigation Without BOSE >> DTC/Circuit Diagnosis >> Rear View Camera Image Signal Circuit >> Diagnosis Procedure >> Without Driver Assistance System
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Without Driver Assistance System

  1. CHECK REVERSE INPUT SIGNAL

    1. Turn ignition switch ON.
    2. Shift the selector lever to R (reverse).
    3. Check voltage between AV control unit connector M97 and ground.
      AV control unit Ground Condition Voltage
      (Approx.)
      (+) (-)
      Connector Terminal
      M97 25 - Selector lever in R (reverse) Battery Voltage

    Is inspection result normal?

    YES 

    GO TO STEP 2  .

    NO 

    Repair or replace harness or connectors.

  2. CHECK CAMERA POWER SUPPLY CIRCUIT CONTINUITY

    1. Turn ignition switch OFF.
    2. Disconnect AV control unit connector M97 and rear view camera connector.
    3. Check continuity between AV control unit connector M97 and rear view camera connector B35.
      AV control unit Rear view camera Continuity
      Connector Terminal Connector Terminal
      M97 43 B35 8 Yes
    4. Check continuity between AV control unit connector M97 and ground.
      AV control unit Ground Continuity
      Connector Terminal
      M97 43 No

    Is inspection result normal?

    YES 

    GO TO STEP 3  .

    NO 

    Repair or replace harness or connectors.

  3. CHECK CAMERA POWER SUPPLY VOLTAGE

    1. Connect AV control unit connector M97 and rear view camera connector.
    2. Turn ignition switch ON.
    3. Shift the selector lever to R (reverse).
    4. Check voltage between AV control unit connector M97 and ground.
      AV control unit Ground Condition Voltage
      (Approx.)
      (+) (-)
      Connector Terminal
      M97 43 - Selector lever is in "R". 6.0 V

    Is inspection result normal?

    YES 

    GO TO STEP 4  .

    NO 

    Replace AV control unit. Refer to REMOVAL AND INSTALLATION .

  4. CHECK CAMERA IMAGE SIGNAL CIRCUIT CONTINUITY

    1. Turn ignition switch OFF.
    2. Disconnect AV control unit connector M97 and rear view camera connector.
    3. Check continuity between AV control unit connector M97 and rear view camera connector B35.
      AV control unit Rear view camera Continuity
      Connector Terminal Connector Terminal
      M97 41 B35 5 Yes
    4. Check continuity between AV control unit connector M97 terminal 82 and ground.
      AV control unit Ground Continuity
      Connector Terminal
      M97 41 No

    Is inspection result normal?

    YES 

    GO TO STEP 5  .

    NO 

    Repair or replace harness or connectors.

  5. CHECK CAMERA GROUND CIRCUIT CONTINUITY

    Check continuity between AV control unit connector M97 and rear view camera connector B35.

    AV control unit Rear view camera Continuity
    Connector Terminal Connector Terminal
    M97 44 B35 7 Yes

    Is inspection result normal?

    YES 

    GO TO STEP 6  .

    NO 

    Repair or replace harness or connectors.

  6. CHECK CAMERA IMAGE SIGNAL

    1. Connect AV control unit connector M97 and rear view camera connector.
    2. Turn ignition switch ON.
    3. Shift the selector lever to R (reverse).
    4. Check signal between AV control unit connector M97 and ground.
      AV control unit Ground Condition Reference value
      (+) (-)
      Connector Terminal
      M97 41 - Camera image displayed.
      G00498910Courtesy of NISSAN NORTH AMERICA, INC.

    Is inspection result normal?

    YES 

    Replace AV control unit. Refer to REMOVAL AND INSTALLATION .

    NO 

    Replace rear view camera. Refer to REMOVAL AND INSTALLATION .

scientia non olet · About LEMON Manuals