LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2015 >> Altima Base >> Repair and Diagnosis >> Accessories & Equipment >> Warning Systems >> Driver Assistance System - Intelligent Technology Suite (Its) Control Unit And Lane Departure Warning (LDW) >> Its Control Unit >> Basic Inspection >> Rear View Camera Calibration >> Work Procedure (Target Setting)
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Work Procedure (Target Setting)

CAUTION:
  • Perform this operation in a horizontal position where there is a clear view for 3 m (9.84 ft) backward and 4 m (13.12 ft) wide.
  • Place the target in a well-lighted location. (Poor lighting may make it hard to adjust.)
  • The target may not be detected when it shines by the reflected light of the sun or lighting.
  • The target may not be detected when there is the same pattern of black and white as the target when the pattern is within 0.5 m (1.64 ft) from either side and upward/downward position from the target. (It is desirable that the vehicle is positioned on a single-color floor.)

  1. TARGET SETTING

    Fig 1: Target Setting Dimensions
    G08687240Courtesy of NISSAN NORTH AMERICA, INC.
    Side distance (Sd ): "B"-"E" ("D"-"F") : 2125 mm (83.66 in)
    Left distance (Ld ): "Ct "-"Lt " : 1500 mm (59.06 in)
    Right distance (Rd ): "Ct "-"Rt " : 1500 mm (59.06 in)
    1. Mark points "A", "B", "C" and "D" at the center of the lateral surface of each wheel.
      Fig 2: Marking Point At Center Of Lateral Surface Of Wheel Using String And Cone
      G04140641Courtesy of NISSAN NORTH AMERICA, INC.
      NOTE:

      Hang a string with a cone from the fender so as to pass through the center of wheel, and then mark a point at the center of the lateral surface of the wheel.

    2. Draw line "LH" passing through points "A" and "B" on the left side of vehicle.
      NOTE:

      Approximately 2.2 m (7.22 ft) or more at the rear from the rear axle.

    3. Mark point "E" on the line "LH" at the positions 2125 mm (83.66 in) from point "B".
    4. Draw line "RH" passing through points "C" and "D" on the right side of vehicle in the same way as step 2.
    5. Mark point "F" on the line "RH" at the positions 2125 mm (83.66 in) from point "D".
    6. Draw line "RW" passing through the points "E" and "F" on the rear of the vehicle.
      NOTE:

      Approximately 1.8 m (5.91 ft) or more at both left and right sides from vehicle center.

    7. Mark point "Ct " at the center of point "E" and "F" on the line "RW".
      CAUTION:

      Make sure that "E" to "Ct " is equal to "F" to "Ct ".

    8. Mark point "Lt" and "Rt" on the line "RW" at the positions 1500 mm (59.06 in) from point "Ct".
    9. Position the center of the target mark to point of "Ct".
    Fig 3: Locating Target Marking Positions From Center, Left And Right
    G08687242Courtesy of NISSAN NORTH AMERICA, INC.
    CAUTION:

    Make sure that the black/white pattern of the center target is rotated as compared with the left and right targets.

    Go to WORK PROCEDURE (REAR VIEW CAMERA CALIBRATION) .

scientia non olet · About LEMON Manuals