| REQ SW -DR [On/Off] |
* |
Indicates condition of door request switch LH. |
| REQ SW -AS [On/Off] |
* |
Indicates condition of door request switch RH. |
| REQ SW -BD/TR [On/Off] |
* |
Indicates condition of back door request switch. |
| PUSH SW [On/Off] |
|
Indicates condition of push-button ignition switch. |
| BRAKE SW 1 [On/Off] |
* |
Indicates condition of brake pedal position switch. |
| BRAKE SW 2 [On/Off] |
|
Indicates condition of stop lamp switch. |
| DETE/CANCL SW [On/Off] |
* |
Indicates condition of park position switch. |
| PUSH SW -IPDM [On/Off] |
|
Indicates condition of push-button ignition switch received from IPDM E/R on CAN communication line. |
| IGN RLY1 -F/B [On/Off] |
|
Indicates condition of ignition relay 1 received from IPDM E/R on CAN communication line. |
| NEUTRAL SW -IPDM [On/Off] |
|
Indicates condition of transmission range switch received from IPDM E/R on CAN communication line. |
| SFT PN -IPDM [On/Off] |
|
Indicates condition of P (park) or N (neutral) position from TCM on CAN communication line. |
| STARTER RELAY -IPDM [On/Off] |
|
Indicates condition of starter relay received from IPDM E/R on CAN communication line. |
| ENGINE STATE [STOP/START/CRANK/RUN] |
* |
Indicates condition of engine state from ECM on CAN communication line. |
| ST/INH RELAY - IPDM [On/Off] |
|
Indicates condition of starter relay and starter control relay status signal from IPDM E/R. |
| REVERSE SIGNAL -IPDM [On/Off] |
|
Indicates condition of transmission range switch received from IPDM E/R on CAN communication line. |
| CRANKING PERMIT -ECM [PERMIT] |
|
Indicates condition of engine start possibility from ECM on CAN communication line. |
| IS STATUS -ECM [On/Off] |
|
Indicates IS status from ECM on CAN communication line. |
| STARTER CUT RELAY -ECM [On/Off] |
|
Indicates condition of starter cut relay from ECM on CAN communication line. |
| VEH SPEED 1 [mph/km/h] |
* |
Indicates condition of vehicle speed signal received from ABS on CAN communication line. |
| VEH SPEED 2 [mph/km/h] |
* |
Indicates condition of vehicle speed signal received from combination meter on CAN communication line. |
| IGN REQ -IPDM [On/Off] |
|
Indicates condition of ignition request from IPDM E/R on CAN communication line. |
| STARTER REQ -IPDM [On/Off] |
|
Indicates condition of starter request received from IPDM E/R on CAN communication line. |
| DOOR STAT -DR [LOCK/READY/UNLK] |
* |
Indicates condition of driver side door status. |
| DOOR STAT -AS [LOCK/READY/UNLK] |
* |
Indicates condition of passenger side door status. |
| DOOR STAT -RR [LOCK/READY/UNLK] |
* |
Indicates condition of rear right side door status. |
| DOOR STAT -RL [LOCK/READY/UNLK] |
* |
Indicates condition of rear left side door status. |
| BK DOOR STATE [LOCK/READY/UNLK] |
* |
Indicates condition of back door status. |
| ID OK FLAG [Set/Reset] |
|
Indicates condition of Intelligent Key ID. |
| PRMT ENG STRT [Set/Reset] |
|
Indicates condition of engine start possibility. |
| PRMT RKE STRT [Set/Reset] |
|
Indicates condition of engine start possibility from Intelligent Key. |
| I-KEY OK FLAG [Key ON/Key OFF] |
* |
Indicates condition of Intelligent Key OK flag. |
| PRBT ENG STRT [Set/Reset] |
|
Indicates condition of engine start prohibit. |
| ID AUTHENT CANCEL TIMER [STOP] |
|
Indicates condition of Intelligent Key ID authentication. |
| ACC BATTERY SAVER [STOP] |
|
Indicates condition of battery saver. |
| CRNK PRBT TMR [On/Off] |
|
Indicates condition of crank prohibit timer. |
| AUT CRNK TMR [On/Off] |
|
Indicates condition of automatic engine crank timer from Intelligent Key. |
| CRNK PRBT TME [sec] |
|
Indicates condition of engine crank prohibit time. |
| AUTO CRNK TME [sec] |
|
Indicates condition of automatic engine crank time from Intelligent Key. |
| CRANKING TME [sec] |
|
Indicates condition of engine cranking time from Intelligent Key. |
| RKE OPE COUN1 [0-19] |
* |
When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the numerical value start changing. |
| RKE OPE COUN2 [0-19] |
* |
When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the numerical value start changing. |
| RKE-LOCK [On/Off] |
|
Indicates condition of lock signal from Intelligent Key. |
| RKE-UNLOCK [On/Off] |
|
Indicates condition of unlock signal from Intelligent Key. |
| RKE-TR/BD [On/Off] |
|
Indicates condition of back door open signal from Intelligent Key. |
| RKE-PANIC [On/Off] |
|
Indicates condition of panic signal from Intelligent Key. |
| RKE-MODE CHG [On/Off] |
|
Indicates condition of mode change signal from Intelligent Key. |
| RKE PBD [On/Off] |
|
Indicates condition of automatic back door signal from Intelligent Key. |