| REQ SW -DR [On/Off] |
* |
Indicates condition of door request switch LH |
| REQ SW -AS [On/Off] |
* |
Indicates condition of door request switch RH |
| REQ SW -BD/TR [On/Off] |
* |
Indicates condition of trunk opener request switch |
| PUSH SW [On/Off] |
|
Indicates condition of push button ignition switch |
| SHFTLCK SLNID PWR SPLY [On/Off] |
|
Indicates condition of shiftlock solenoid power supply |
| BRAKE SW 1 [On/Off] |
* |
Indicates condition of brake switch |
| BRAKE SW 2 [On/Off] |
|
Indicates condition of brake switch |
| DETE/CANCL SW [On/Off] |
* |
Indicates condition of P position |
| SFT PN/N SW [On/Off] |
* |
Indicates condition of P or N position |
| UNLK SEN -DR [On/Off] |
* |
Indicates condition of door unlock sensor |
| PUSH SW -IPDM [On/Off] |
|
Indicates condition of push button ignition switch received from IPDM E/R on CAN communication line |
| IGN RLY1 -F/B [On/Off] |
|
Indicates condition of ignition relay 1 received from IPDM E/R on CAN communication line |
| DETE SW -IPDM [On/Off] |
|
Indicates condition of detent switch received from TCM on CAN communication line |
| SFT PN -IPDM [On/Off] |
|
Indicates condition of P or N position from TCM on CAN communication line |
| SFT P -MET [On/Off] |
|
Indicates condition of P position from TCM on CAN communication line |
| SFT N -MET [On/Off] |
|
Indicates condition of N position from IPDM E/R on CAN communication line |
| ENGINE STATE [Stop/Start/Crank/Run] |
* |
Indicates condition of engine state from ECM on CAN communication line |
| VEH SPEED 1 [mph/km/h] |
* |
Indicates condition of vehicle speed signal received from ABS on CAN communication line |
| VEH SPEED 2 [mph/km/h] |
* |
Indicates condition of vehicle speed signal received from combination meter on CAN communication line |
| DOOR STAT -DR [LOCK/READY/UNLK] |
* |
Indicates condition of driver side door status. |
| DOOR STAT -AS [LOCK/READY/UNLK] |
* |
Indicates condition of passenger side door status. |
| DOOR STAT -RR [LOCK/READY/UNLK] |
* |
Indicates condition of rear right side door status. |
| DOOR STAT -RL [LOCK/READY/UNLK] |
* |
Indicates condition of rear left side door status. |
| ID OK FLAG [Set/Reset] |
|
Indicates condition of Intelligent Key ID |
| PRMT ENG START [Set/Reset] |
|
Indicates condition of engine start possibility from Intelligent Key |
| I-KEY OK FLAG [Set/Reset] |
|
Indicates condition of Intelligent Key ID. |
| ID AUTHENT CANCEL TIMER [under a stop] |
|
Indicates condition of Intelligent Key ID authentication. |
| ACC BATTERY SAVER [under a stop] |
|
Indicates condition of battery saver. |
| CRNK PRBT TMR [On/Off] |
|
Indicates condition of crank prohibit timer. |
| AUT CRNK TMR [On/Off] |
|
Indicates condition of automatic engine crank timer from Intelligent Key. |
| CRANKING TME [sec] |
|
Indicates condition of engine cranking time from Intelligent Key. |
| SHORT CRANK |
|
Indicates condition of condition of short crank from Intelligent Key |
| ST RLY -REQ |
|
Indicates condition of starter relay. |
| IGN RLY 1 -REQ |
|
Indicates condition of ignition 1 relay. |
| IGN RLY 2 -REQ |
|
Indicates condition of ignition 2 relay. |
| DETE SW PWR [On/Off] |
|
Indicates condition of park position switch voltage. |
| IGN RLY 3 -REQ |
|
Indicates condition of ignition 3 relay. |
| ACC RLY -REQ |
|
Indicates condition of ACC relay. |
| PRBT ENG STRT [Set/Reset] |
|
Indicates condition of engine start possibility. |
| PRMT RKE STRT [Set/Reset] |
|
Indicates condition of engine start possibility from Intelligent Key. |
| TRNK/HAT MNTR [On/Off] |
|
Indicates condition of trunk lid. |
| RKE-LOCK [On/Off] |
|
Indicates condition of lock signal from Intelligent Key. |
| RKE-UNLOCK [On/Off] |
|
Indicates condition of unlock signal from Intelligent Key. |
| RKE-TR/BD [On/Off] |
|
Indicates condition of trunk open signal from Intelligent Key. |
| RKE-PANIC [On/Off] |
|
Indicates condition of panic signal from Intelligent Key. |
| RKE-MODE CHG [On/Off] |
|
Indicates condition of mode change signal from Intelligent Key. |
| RKE OPE COUN1 [0-19] |
* |
When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the numerical value start changing. |
| RKE OPE COUN2 [0-19] |
* |
When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the numerical value start changing. |