Data Monitor
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items.
| Monitor Item | Condition |
|---|---|
| REQ SW -DR | Indicates [On/Off] condition of door request switch (driver side) |
| REQ SW -AS | Indicates [On/Off] condition of door request switch (passenger side) |
| REQ SW -BD/TR | Indicates [On/Off] condition of back door request switch |
| PUSH SW | Indicates [On/Off] condition of push-button ignition switch |
| CLUTCH SW * 1 | Indicates [On/Off] condition of clutch interlock switch |
| BRAKE SW 1 | Indicates [On/Off] * 2 condition of stop lamp switch power supply |
| BRAKE SW 2 | Indicates [On/Off] condition of stop lamp switch |
| DETE/CANCL SW | Indicates [On/Off] condition of P position |
| START CLUTCH SW | Indicates [On/Off] condition of clutch pedal position switch |
| PUSH SW -IPDM | Indicates [On/Off] condition of push-button ignition switch |
| IGN RLY1 -F/B | Indicates [On/Off] condition of ignition relay 1 |
| NEUTRAL SW - IPDM |
NOTE:
This item is displayed, but cannot be monitored |
| SFT PN -IPDM | Indicates [On/Off] condition of P or N position |
| STARTER RELAY - IPDM | Indicates [On/Off] condition of starter relay |
| ENGINE STATE | Indicates [Stop/Stall/Crank/Run] condition of engine states |
| ST/INHI RELAY-IPDM | Display the starter relay/starter control relay status signal from IPDM E/R via CAN communication |
| REVERSE SIGNAL - IPDM | Indicates [On/Off] condition of R position |
| CRANKING PERMIT - ECM | Display the engine cranking permit signal from ECM via CAN communication |
| IS STATUS - ECM |
NOTE:
This item is displayed, but cannot be monitored |
| STARTER CUT RELAY - ECM | Indicates [On/Off] condition of starter control relay signal from ECM via CAN communication |
| VEH SPEED 1 | Display the vehicle speed signal received from combination meter by numerical value [Km/h] |
| VEH SPEED 2 | Display the vehicle speed signal received from ABS actuator and electric unit (control unit) by numerical value [Km/h] |
| IGN REQ - IPDM | Display the ignition request signal from IPDM E/R via CAN communication |
| STARTER REQ - IPDM | Display the starter request signal from IPDM E/R via CAN communication |
| DOOR STAT-DR | Indicates [LOCK/READY/UNLK] condition of driver door status |
| DOOR STAT-AS | Indicates [LOCK/READY/UNLK] condition of passenger door status |
| DOOR STAT-RR | Indicates [LOCK/READY/UNLK] condition of rear door RH status |
| DOOR STAT-RL | Indicates [LOCK/READY/UNLK] condition of rear door LH status |
| BK DOOR STATE |
NOTE:
This item is displayed, but cannot be monitored |
| ID OK FLAG | Indicates [Set/Reset] condition of Intelligent Key ID |
| PRMT ENG STRT | Indicates [Set/Reset] condition of engine start possibility |
| PRMT RKE STRT |
NOTE:
This item is displayed, but cannot be monitored |
| I-KEY OK FLAG | Indicates [KEY On/NOT On] condition of Intelligent Key ID and Intelligent Key is detected inside vehicle |
| PRBT ENG STRT | Indicates whether or not the engine is in start prohibited status |
| ID AUTHENT CANCEL TIMER | Indicates whether or not it is in engine start possible status when Intelligent Key verification is unnecessary |
| ACC BATTERY SAVER |
NOTE:
This item is displayed, but cannot be monitored |
| CRNK PRBT TMR | Indicates [On/Off] whether or not in cranking prohibited status due to starter motor protection function operation |
| AUT CRANK TMR | Indicates [On/Off] whether or not in AUTO CRANKING MODE status |
| CRNK PRBT TME | Indicates the time for changing from cranking prohibited status to cranking possible status |
| AUT CRANK TMR | Indicates the time that AUTO CRANKING MODE operates |
| CRANKING TME | Indicates the cranking operation time |
| SHORT CRANK |
NOTE:
This item is displayed, but not used |
| RKE OPE COUN1 | When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the numerical value start changing |
| RKE OPE COUN2 |
NOTE:
This item is displayed, but not used |
| STOP/START SW |
NOTE:
This item is displayed, but cannot be monitored |
| RKE-LOCK | Indicates [On/Off] condition of LOCK signal from Intelligent Key |
| RKE-UNLOCK | Indicates [On/Off] condition of UNLOCK signal from Intelligent Key |
| RKE-TR/BD |
NOTE:
This item is displayed, but cannot be monitored |
| RKE-PANIC | Indicates [On/Off] condition of panic alarm signal from Intelligent Key |
| RKE-MODE CHG | Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key |
| RKE PBD |
NOTE:
This item is displayed, but cannot be monitored |
* 1 : It is displayed but does not operate on CVT models.
* 2 : OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.