Data Monitor
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items.
| Monitor Item [Unit] |
Description |
|---|---|
| REVERSE SIGNAL [Open/Close] |
|
| IGN RELAY [Open/Close] |
Displays the status of the ignition relay judged by IPDM E/R. |
| PUSH SW [Open/Close] |
Displays the status of the push - button ignition switch judged by IPDM E/R. |
| NEUTRAL SW [Open/Close] |
Displays the status of the neutral position switch (M/T) judged by IPDM E/R. |
| INTERLOCK/PNP SW [Open/Close] |
Displays the status of the transmission range switch (CVT) judged by IPDM E/R. |
| OIL PRESSURE SW [Open/Close] |
NOTE:
The item is indicated, but not monitored. |
| LED H/L RH STATUS [Open/Close] |
Displays the LED headlamp (right) ON/OFF status judged by IPDM E/R.
NOTE:
The item is monitored only on the vehicle with LED headlamp. |
| LED H/L LH STATUS [Open/Close] |
Displays the LED headlamp (left) ON/OFF status judged by IPDM E/R.
NOTE:
The item is monitored only on the vehicle with LED headlamp. |
| HOOD SW [Open/Close] |
Displays the status of the hood switch judged by IPDM E/R. |
| COMPRESSOR [Off/On] |
Displays the compressor drive status judged by IPDM E/R. |
| H/L WASHER PUMP [Off/On] |
NOTE:
The item is indicated, but not monitored. |
| HORN RELAY [Off/On] |
Displays the status of the horn relay judged by IPDM E/R. |
| COOLING FAN [Off/On] |
NOTE:
The item is indicated, but not monitored. |
| FRONT WIPER HI/LO RELAY [Off/On] |
Displays the front wiper HI/LO relay drive status judged by IPDM E/R. |
| FRONT WIPER RELAY [Off/On] |
Displays the front wiper relay drive status judged by IPDM E/R. |
| IGN RELAY OFF STATUS [Off/On] |
Displays the status of the ignition relay OFF circuit judged by IPDM E/R. |
| IGN RELAY ON STATUS [Off/On] |
Displays the status of the ignition relay ON circuit judged by IPDM E/R. |
| STEERING LOCK PWR SPLY [Off/On] |
NOTE:
The item is indicated, but not monitored. |
| HEIGHT SENSOR PWR SPLY [Off/On] |
NOTE:
The item is indicated, but not monitored. |
| COOLING FAN RELAY 1 [Off/On] |
Displays the status of the cooling fan relay-1 judged by IPDM E/R. |
| STARTER RELAY [Off/On] |
Displays the status of the starter control relay judged by IPDM E/R. |
| COMP ECV DUTY [%] |
Displays the compressor control signal (PWM) status of IPDM E/R. |
| COOLING FAN RELAY 2 [%] |
Displays the status of the cooling fan relay-2 judged by IPDM E/R. |
| FR FOG LAMP LH [%] |
Displays the front fog lamp (left) output (PWM) status of IPDM E/R. |
| FR FOG LAMP RH [%] |
Displays the front fog lamp (right) output (PWM) status of IPDM E/R. |
| LEVELIZER OUTPUT [%] |
NOTE:
The item is indicated, but not monitored. |
| PARKING LAMP [%] |
Displays the parking lamp output (PWM) status of IPDM E/R. |
| TAIL LAMP LH [%] |
Displays the tail lamp (left) output (PWM) status of IPDM E/R. |
| TAIL LAMP RH [%] |
Displays the tail lamp (right) output (PWM) status of IPDM E/R. |
| DAYTIME RUNNING LIGHT LH [%] |
Displays the daytime running light (left) output status of IPDM E/R. |
| DAYTIME RUNNING LIGHT RH [%] |
Displays the daytime running light (right) output status of IPDM E/R. |
| HEADLAMP (HI) LH [%] |
Displays the headlamp (HI) (left) output (PWM) status of IPDM E/R. |
| HEADLAMP (HI) RH [%] |
Displays the headlamp (HI) (right) output (PWM) status of IPDM E/R. |
| HEADLAMP (LO) LH [%] |
Displays the headlamp (LO) (left) output (PWM) status of IPDM E/R. |
| HEADLAMP (LO) RH [%] |
Displays the headlamp (LO) (right) output (PWM) status of IPDM E/R. |
| A/C RELAY STUCK [OK/NG] |
Displays the ON stuck status of the A/C relay judged by IPDM E/R. |
| A/C RELAY [Off/On] |
Displays the status of the A/C relay judged by IPDM E/R. |
| COMP ECV STATUS [OK/NG] |
Displays the compressor malfunction diagnosis status judged by IPDM E/R. |
| VEHICLE SECURITY HORN [Off/On] |
NOTE:
The item is indicated, but not monitored. |
| BATTERY CURRENT SENSOR [OK/NG] |
Displays the battery current sensor malfunction diagnosis status judged by IPDM E/R. |
| FRONT FOG LAMP [Off/On] |
Displays the fog lamp illumination control status of IPDM E/R. |
| COMP ECV CURRENT [A] |
Displays the electric current output to compressor judged by IPDM E/R. |
| BATTERY VOLTAGE [V] |
Displays the status of the battery voltage judged by IPDM E/R. |
| COOLING FAN DUTY [%] |
Displays the cooling fan output signal status of IPDM E/R. |
| HOOD SW (CAN) [Open/Close/NG] |
Displays the status of the hood switch judged by IPDM E/R. |
| FRONT WIPER [STOP/HIGH/LOW/NG] |
Displays the front wiper motor drive control status of IPDM E/R. |
| FR WIPER STOP POSITION [ACTIVE P/STOP P] |
Displays the status of the front wiper position status judged by IPDM E/R. |
| HEADLAMP (HI) [Off/On] |
Displays the headlamp (HI) illumination control status of IPDM E/R. |
| HEADLAMP (LO) [Off/On] |
Displays the headlamp (LO) illumination control status of IPDM E/R. |
| IGNITION RELAY STATUS [Off/On] |
Displays the ignition relay output status of IPDM E/R. |
| IGN RELAY MONITOR [Off/On] |
Displays the status of the ignition relay judged by IPDM E/R. |
| IGNITION POWER SUPPLY [Off/On] |
Displays the status of the ignition power supply judged by IPDM E/R. |
| INTERLOCK/PNP SW (CAN) [Off/On] |
Displays the status of the transmission range switch signal that IPDM E/R transmits via CAN communication. |
| NEUTRAL SWITCH (CAN) [Off/On/NG] |
Displays the status of the neutral position switch (M/T) signal that IPDM E/R transmits via CAN communication. |
| PUSH-BUTTON IGN SW (CAN) [Off/On] |
Displays the status of the ignition switch signal that IPDM E/R transmits via CAN communication. |
| TAIL LAMP [Off/On] |
Displays the tail lamp illumination control status of IPDM E/R. |
| REVERSE SIGNAL (CAN) [Off/On/NG] |
Displays the status of the reverse switch (M/T) signal that IPDM E/R transmits via CAN communication. |
| ST&ST CONT RELAY STATUS [Off/Off, ON/ST R On] |
Displays the status of the start control relay and start motor relay status judged by IPDM E/R. |
| STARTER MOTOR STATUS [Off/On/L-TIME] |
Displays the status of the starter motor judged by IPDM E/R. |
| STARTER RELAY (CAN) [LOW/HIGH/NG] |
Displays the status of the IPDM E/R transmits the starter control relay status signal via CAN communication. |
| IPDM NOT SLEEP [NO RDY/READY] |
Displays the status of the IPDM E/R transmits the not sleep signal via CAN communication. |
| AFTER COOLING TIME [No request/0.5min/1.0min/1.5min/2.0min/2.5min/3.0min/3.5min/4min/5min/6min/8min/10min/12min/14min/16min] |
NOTE:
The item is indicated, but not monitored. |
| AFTER COOLING SPEED [0%/25%/40%/55%/70%/78%/85%/100%] |
NOTE:
The item is indicated, but not monitored. |
| COOLING FAN TYPE [RENAULT/NISSAN] |
NOTE:
The item is indicated, but not monitored. |
| COMPRESSOR REQ 1 [Off/On] |
Displays the status of the A/C compressor request signal received from ECM via CAN communication. |
| VHCL SECRITY HORN REQ [Off/On] |
NOTE:
The item is indicated, but not monitored. |
| DTRL REQ [Off/On] |
Displays the status of the daytime running light request signal received from BCM via CAN communication. |
| SLEEP/WAKE UP [SLEEP/WAKEUP] |
NOTE:
The item is indicated, but not monitored. |
| CLUTCH INTERLOCK SW [Off/On/NG] |
NOTE:
The item is indicated, but not monitored. |
| CRANKING ENABLE-TCM [OK/NG] |
Displays the status of the cranking enable signal received from TCM via CAN communication. |
| CRANKING ENABLE-ECM [OK/NG/STOP/No request] |
Displays the status of the cranking enable signal received from ECM via CAN communication. |
| CAN DIAGNOSIS [OK/NG] |
Displays the status of the CAN diagnosis signal received from BCM via CAN communication. |
| FRONT FOG LAMP REQ [Off/On] |
Displays the status of the front fog light request signal received from BCM via CAN communication. |
| H/L WASHER REQ [Off/On] |
NOTE:
The item is indicated, but not monitored. |
| PASSING REQ [Off/On] |
NOTE:
The item is indicated, but not monitored. |
| HIGH BEAM REQ [Off/On] |
Displays the status of the high beam request signal received from BCM via CAN communication. |
| HORN CHIRP [Off/On] |
Displays the status of the horn reminder signal received from BCM via CAN communication. |
| COOLING FAN REQ [%] |
Displays the status of the cooling fan speed request signal received from ECM via CAN communication. |
| ENGINE STATUS [STOP/IDLING/RUN] |
Displays the status of the engine status signal received from ECM via CAN communication. |
| TURN SIGNAL REQ [Off/LH/RH] |
Displays the status of the turn indicator signal received from BCM via CAN communication. |
| FR WIPER REQ [RETURN/STOP/NG/LOW/HIGH] |
Displays the status of the front wiper request signal received from BCM via CAN communication. |
| SHIFT POSITION [OFF/P/R/N/D/S/L/B/1/2/3/4/5/6/7] |
Displays the status of the shift position signal received from TCM via CAN communication. |
| LOW BEAM REQ [Off/On] |
Displays the status of the low beam request signal received from BCM via CAN communication. |
| POSITION LIGHT REQ [Off/On] |
Displays the status of the position light request signal received from BCM via CAN communication. |
| COMPRESSOR REQ 2 [Off/On] |
Displays the status of the A/C ON signal received from A/C auto amp. via CAN communication. |
| IGNITION SW [Off/On/START/No request] |
Displays the status of the ignition switch ON signal and starter control relay request signal received from BCM via CAN communication. |
| VEHICLE SPEED (METER) [km/h] |
Displays the status of the vehicle speed signal received from combination meter via CAN communication. |
| BAT DISCHARGE COUNT [-] |
Monitor the cumulative discharge value of the battery.
NOTE:
When 65, 000 or more is counted, replace the battery. |
| P LAMP CIRC MALFUNCTN [0 - 1] |
Monitor the number of times that the smart FET in IPDM E/R reaches the retry upper limit of the parking lamp circuit.
NOTE:
When the number of parking lamp circuit retries count is 20, this item counts 1. |
| NMB P LAMP CIRC RETRY [0 - 20] |
Monitor the number of times that the smart FET in IPDM E/R permits the retry of the parking lamp circuit.
NOTE:
When the number of short circuits in the parking lamp circuit count is 5 and the ignition switch OFF to ON operation is detected, this item counts 1. |
| NMB P LAMP CIRC SHORT [0 - 5] |
Monitor the number of times that the smart FET in IPDM E/R detects the over current of the parking lamp circuit. |
| DTRL LH CIRC MALFUNCTN [0 - 1] |
Monitor the number of times that the smart FET in IPDM E/R reaches the retry upper limit of the daytime running light (left) circuit.
NOTE:
When the number of daytime running light (left) circuit retries count is 20, this item counts 1. |
| NMB DTRL LH CIRC RETRY [0 - 20] |
Monitor the number of times that the smart FET in IPDM E/R permits the retry of the daytime running light (left) circuit.
NOTE:
When the number of short circuits in the daytime running light (left) circuit count is 5 and the ignition switch OFF to ON operation is detected, this item counts 1. |
| NMB DTRL LH CIRC SHORT [0 - 5] |
Monitor the number of times that the smart FET in IPDM E/R detects the over current of the daytime running light (left) circuit. |
| DTRL RH CIRC MALFUNCTN [0 - 1] |
Monitor the number of times that the smart FET in IPDM E/R reaches the retry upper limit of the daytime running light (right) circuit.
NOTE:
When the number of daytime running light (right) circuit retries count is 20, this item counts 1. |
| NMB DTRL RH CIRC RETRY [0 - 20] |
Monitor the number of times that the smart FET in IPDM E/R permits the retry of the daytime running light (right) circuit.
NOTE:
When the number of short circuits in the daytime running light (right) circuit count is 5 and the ignition switch OFF to ON operation is detected, this item counts 1. |
| NMB DTRL RH CIRC SHORT [0 - 5] |
Monitor the number of times that the smart FET in IPDM E/R detects the over current of the daytime running light (right) circuit. |
| F FOG LH CIRC MALFUNCTN [0 - 1] |
Monitor the number of times that the smart FET in IPDM E/R reaches the retry upper limit of the front fog lamp (left) circuit.
NOTE:
When the number of front fog lamp (left) circuit retries count is 20, this item counts 1. |
| NMB F FOG LH CIRC RETRY [0 - 20] |
Monitor the number of times that the smart FET in IPDM E/R permits the retry of the front fog lamp (left) circuit.
NOTE:
When the number of short circuits in the front fog lamp (left) circuit count is 5 and the ignition switch OFF to ON operation is detected, this item counts 1. |
| NMB F FOG LH CIRC SHORT [0 - 5] |
Monitor the number of times that the smart FET in IPDM E/R detects the over current of the front fog lamp (left) circuit. |
| F FOG RH CIRC MALFUNCTN [0 - 1] |
Monitor the number of times that the smart FET in IPDM E/R reaches the retry upper limit of the front fog lamp (right) circuit.
NOTE:
When the number of front fog lamp (right) circuit retries count is 20, this item counts 1. |
| NMB F FOG RH CIRC RETRY [0 - 20] |
Monitor the number of times that the smart FET in IPDM E/R permits the retry of the front fog lamp (right) circuit.
NOTE:
When the number of short circuits in the front fog lamp (right) circuit count is 5 and the ignition switch OFF to ON operation is detected, this item counts 1. |
| NMB F FOG RH CIRC SHORT [0 - 5] |
Monitor the number of times that the smart FET in IPDM E/R detects the over current of the front fog lamp (right) circuit. |
| HL (HI) LH CIRC MALFUNCTN [0 - 1] |
Monitor the number of times that the smart FET in IPDM E/R reaches the retry upper limit of the headlamp (HI) (left) circuit.
NOTE:
When the number of headlamp (HI) (left) circuit retries count is 20, this item counts 1. |
| NMB HL (HI) LH CIRC RETRY [0 - 20] |
Monitor the number of times that the smart FET in IPDM E/R permits the retry of the headlamp (HI) (left) circuit.
NOTE:
When the number of short circuits in the headlamp (HI) (left) circuit count is 5 and the ignition switch OFF to ON operation is detected, this item counts 1. |
| NMB HL (HI) LH CIRC SHORT [0 - 5] |
Monitor the number of times that the smart FET in IPDM E/R detects the over current of the headlamp (HI) (left) circuit. |
| HL (HI) RH CIRC MALFUNCTN [0 - 1] |
Monitor the number of times that the smart FET in IPDM E/R reaches the retry upper limit of the headlamp (HI) (right) circuit.
NOTE:
When the number of headlamp (HI) (right) circuit retries count is 20, this item counts 1. |
| NMB HL (HI) RH CIRC RETRY [0 - 20] |
Monitor the number of times that the smart FET in IPDM E/R permits the retry of the headlamp (HI) (right) circuit.
NOTE:
When the number of short circuits in the headlamp (HI) (right) circuit count is 5 and the ignition switch OFF to ON operation is detected, this item counts 1. |
| NMB HL (HI) RH CIRC SHORT [0 - 5] |
Monitor the number of times that the smart FET in IPDM E/R detects the over current of the headlamp (HI) (right) circuit. |
| S/L CIRC MALFUNCTN [0 - 1] |
NOTE:
The item is indicated, but not monitored. |
| NMB S/L CIRC RETRY [0 - 20] |
NOTE:
The item is indicated, but not monitored. |
| NMB S/L CIRC SHORT [0 - 5] |
NOTE:
The item is indicated, but not monitored. |
| HL (LO) LH CIRC MALFUNCTN [0 - 1] |
Monitor the number of times that the smart FET in IPDM E/R reaches the retry upper limit of the headlamp (LO) (left) circuit.
NOTE:
When the number of headlamp (LO) (left) circuit retries count is 20, this item counts 1. |
| NMB HL (LO) LH CIRC RETRY [0 - 20] |
Monitor the number of times that the smart FET in IPDM E/R permits the retry of the headlamp (LO) (left) circuit.
NOTE:
When the number of short circuits in the headlamp (LO) (left) circuit count is 5 and the ignition switch OFF to ON operation is detected, this item counts 1. |
| NMB HL (LO) LH CIRC SHORT [0 - 5] |
Monitor the number of times that the smart FET in IPDM E/R detects the over current of the headlamp (LO) (left) circuit. |
| HL (LO) RH CIRC MALFUNCTN [0 - 1] |
Monitor the number of times that the smart FET in IPDM E/R reaches the retry upper limit of the headlamp (LO) (right) circuit.
NOTE:
When the number of headlamp (LO) (right) circuit retries count is 20, this item counts 1. |
| NMB HL (LO) RH CIRC RETRY [0 - 20] |
Monitor the number of times that the smart FET in IPDM E/R permits the retry of the headlamp (LO) (right) circuit.
NOTE:
When the number of short circuits in the headlamp (LO) (right) circuit count is 5 and the ignition switch OFF to ON operation is detected, this item counts 1. |
| NMB HL (LO) RH CIRC SHORT [0 - 5] |
Monitor the number of times that the smart FET in IPDM E/R detects the over current of the headlamp (LO) (right) circuit. |
| T LAMP LH CIRC MALFUNCTN [0 - 1] |
Monitor the number of times that the smart FET in IPDM E/R reaches the retry upper limit of the tail lamp (left) circuit.
NOTE:
When the number of tail lamp (left) circuit retries count is 20, this item counts 1. |
| NMB T LAMP LH CIRC RETRY [0 - 20] |
Monitor the number of times that the smart FET in IPDM E/R permits the retry of the tail lamp (left) circuit.
NOTE:
When the number of short circuits in the tail lamp (left) circuit count is 5 and the ignition switch OFF to ON operation is detected, this item counts 1. |
| NMB T LAMP LH CIRC SHORT [0 - 5] |
Monitor the number of times that the smart FET in IPDM E/R detects the over current of the tail lamp (left) circuit. |
| T LAMP RH CIRC MALFUNCTN [0 - 1] |
Monitor the number of times that the smart FET in IPDM E/R reaches the retry upper limit of the tail lamp (right) circuit.
NOTE:
When the number of tail lamp (right) circuit retries count is 20, this item counts 1. |
| NMB T LAMP RH CIRC RETRY [0 - 20] |
Monitor the number of times that the smart FET in IPDM E/R permits the retry of the tail lamp (right) circuit.
NOTE:
When the number of short circuits in the tail lamp (right) circuit count is 5 and the ignition switch OFF to ON operation is detected, this item counts 1. |
| NMB T LAMP RH CIRC SHORT [0 - 5] |
Monitor the number of times that the smart FET in IPDM E/R detects the over current of the tail lamp (right) circuit. |
| BATTERY STATUS [OK/NG] |
Monitor the battery status from the battery output. |
| STARTER OPERATION COUNT | Displays the number of times the starter motor is turned ON. |
| H/P F/PUMP OPERATN COUNT | Displays the number of times the high pressure fuel pump is turned ON. |