Common Specs & Procedures
VERSA NOTE COMMON SPECIFICATIONS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Torque | See Torque Specifications in text and applicable figures in REMOVAL AND INSTALLATION . | ||
| Axle Nut/Hub Bearing Bolts | |||
| Front Axle Nut | 183 Ft. lbs (247.5 N.m) | ||
| Rear Hub Nut | 177 Ft. lbs (240 N.m) | ||
| Rear Spindle Bolts | 62 Ft. lbs. (83.5 N.m) | ||
| Battery | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING BRAKE SYSTEM | ||
| Disc & Drum Brakes | |||
| Front | FRONT DISC BRAKE | ||
| Rear | REAR DRUM BRAKE | ||
| Torque | |||
| Front | See Torque Specifications in text and applicable figures in FRONT DISC BRAKE . | ||
| Rear | See Torque Specifications in text and applicable figures in REAR DRUM BRAKE . | ||
| Charging | |||
| Generator | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Torque | REMOVAL AND INSTALLATION | ||
| Drive Belts | |||
| Adjustment | ADJUSTMENT | ||
| Belt Routing | DRIVE BELT | ||
| Engine Cooling | |||
| General Service Specifications | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Radiator Cap Pressure | 12.8 psi (88 kPa, 0.90 kg/cm2 ) | ||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | NA | ||
| Oil Pressure | |||
| @ Idle | More than 14.2 psi (98 kPa, 1.0 kg/cm2 ) | ||
| @ 2000 RPM | More than 42.6 psi (294 kPa, 3.0 kg/cm2 ) | ||
| @ 6000 RPM | More than 56.8 psi (392 kPa, 4.0 kg/cm2 ) | ||
| Overhaul | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Torque | See Torque Specifications in text and applicable figures in UNIT DISASSEMBLY AND ASSEMBLY . | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate (Drive Plate) Torque | 80 Ft. lbs (108 N.m) | ||
| Fuel System | |||
| Fuel Pressure Release Procedure | FUEL PRESSURE RELEASE | ||
| Fuel Pressure Specification | At Idling: Approximately 51 psi (350 kPa, 3.57 kg/cm2 ) | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE CHECK | ||
| Fuel Filter Location | In Tank Type | ||
| Fuel Filter R & I | FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Engine has coil-on-plug ignition. | ||
| Ignition Wires (Routing) | Engine has coil-on-plug ignition. | ||
| Spark Plugs | Type: NGK PLZKAR6A-11 Gap (nominal):043 in (1.1 mm) Tightening torque: 14 Ft. Lbs (19.6 N.m) |
||
| Starting | |||
| Starter | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Torque | See Torque Specifications in text and applicable figures in REMOVAL AND INSTALLATION . | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Front | WHEEL ALIGNMENT | ||
| Rear | WHEEL ALIGNMENT | ||
| Torque | |||
| Front | See Torque Specifications in text and applicable figures in REMOVAL AND INSTALLATION . | ||
| Rear | See Torque Specifications in text and applicable figures in REMOVAL AND INSTALLATION . | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 83 Ft. lbs (113 N.m, 12 kg.m) | ||
| How To Use Nissan Service Information | |||
| Includes: Standard Bolt Torque Symbol Identification General Connector Info |
GENERAL INFORMATION | ||