Theft Warning Alarm

The theft warning alarm function activates horns and headlamps intermittently when BCM detects that any door or hood is opened by unauthorized means while the system is in the ARMED state.
Security indicator lamp on combination meter always blinks when power supply position is any position other than ON. Security indicator lamp blinking warns that the vehicle is equipped with a vehicle security system.

Operation Flow

Courtesy of NISSAN NORTH AMERICA, INC.

No.	System state	Switching condition
1	DISARMED to PRE-ARMED	When all conditions of A and one condition of B is satisfied.	A	B
			Power supply position: OFF/LOCK All doors: Closed Hood: Closed	All doors are locked by: LOCK button of Intelligent Key Door request switch
2	PRE-ARMED to ARMED	When all of the following conditions are satisfied for 30 seconds.	Power supply position: OFF/LOCK All doors: Locked Hood: Closed
3	ARMED to ALARM	When one condition of A and one condition of B are satisfied.	A	B
			Intelligent Key: Not used	Any door: Open Hood: Open
4	DISARMED to PRE-RESET	When all conditions of A and one condition of B is satisfied.	A	B
			Power supply position: OFF/LOCK All doors: Closed Hood: Open	All doors are locked by: LOCK button of Intelligent Key Door request switch
5	PRE-ARMED to PRE-RESET	When one of the following conditions is satisfied.	Hood: Open
6	ARMED to PRE-RESET	No conditions.
7	ALARM to PRE-RESET
8	PRE-RESET to DISARMED	When one of the following conditions is satisfied.	Power supply position: ACC/ON/CRANKING/RUN UNLOCK button of Intelligent Key: ON Door request switch: ON UNLOCK switch of door lock and unlock switch: ON Any door: Open
9	PRE-RESET to PRE-ARMED	When all of the following conditions are satisfied.	Power supply position: OFF/LOCK All doors: Closed Hood: Closed
10	PRE-ARMED to DISARMED	When one of the following conditions is satisfied.	Power supply position: ACC/ON/CRANKING/RUN UNLOCK button of Intelligent Key: ON Door request switch: ON Any door: Open
11	ARMED to DISARMED	When one of the following conditions is satisfied.	Power supply position: ACC/ON/CRANKING/RUN UNLOCK button of Intelligent Key: ON Door request switch: ON
12	ALARM to DISARMED
13	RE-ALARM	When one of the following conditions is satisfied after the ALARM operation is finished.	Any door: Open Hood: Open

NOTE:

To lock/unlock all doors by operating remote control button of Intelligent Key or door request switch, Intelligent Key must be within the detection area of outside key antenna. For details, refer to System Description .
To open trunk by operating trunk opener switch, Intelligent Key must be within the detection area of outside key antenna. For details, refer to System Description .

DISARMED Phase

The vehicle security system is not set in the DISARMED phase. The vehicle security system stays in this phase while any door is open because it is assumed that the owner is inside or nearby the vehicle. Security indicator lamp blinks every 2.4 seconds.

When the vehicle security system is reset, each phase switches to the DISARMED phase directly.

PRE-ARMED Phase

The PRE-ARMED phase is the transient state between the DISARMED phase and the ARMED phase. This phase is maintained for 30 seconds so that the owner can reset the setting due to a mis-operation. This phase switches to the ARMED phase when vehicle conditions are not changed for 30 seconds. Security indicator lamp illuminates while being in this phase.

To reset the PRE-ARMED phase, refer to the switching condition of No. 10 in the table above.

ARMED Phase

The vehicle security system is set and BCM monitors all necessary inputs. If any door or hood is opened without using Intelligent Key, vehicle security system switches to the ALARM phase. Security indicator lamp blinks every 2.4 seconds.

To reset the ARMED phase, refer to the switching condition of No. 11 in the table above.

ALARM Phase

BCM transmits "Theft Warning Horn Request" signal and "High Beam Request" signal intermittently to IPDM E/R via CAN communication. In this phase, horns and headlamps are activated intermittently for approximately 50 seconds to warn that the vehicle is accessed by unauthorized means. ON/OFF timing of horns and headlamps are synchronized. After 50 seconds, the vehicle security system returns to the ARMED phase. At this time, if BCM still detects unauthorized access to the vehicle, the system is switched to the ALARM phase again. This RE-ALARM operation is carried out a maximum of 2 times.

To cancel the ALARM operation, refer to the switching condition of No. 12 in the table above.

NOTE: If a battery terminal is disconnected during the ALARM phase, theft warning alarm stops. But when the battery terminal is reconnected, theft warning alarm is activated again.

PRE-RESET Phase

The PRE-RESET phase is the transient state between each phase and DISARMED phase. If only the condition of hood is not satisfied, the system switches to the PRE-RESET phase. Then, when any condition is changed, the system switches to the DISARMED phase or PRE-ARMED phase.