Data Monitor
|
Monitor Item [Unit] |
Main |
Description |
|
REQ SW -DR [On/Off] |
x |
Indicates condition of door request switch LH |
|
REQ SW -AS [On/Off] |
x |
Indicates condition of door request switch RH |
|
REQ SW -BD/TR [On/Off] |
x |
Indicates condition of trunk opener request switch |
|
PUSH SW [On/Off] |
Indicates condition of push button ignition switch |
|
|
SHFTLCK SLNID PWR SPLY [On/Off] |
Indicates condition of shiftlock solenoid power supply |
|
|
BRAKE SW 1 [On/Off] |
x |
Indicates condition of brake switch |
|
BRAKE SW 2 [On/Off] |
Indicates condition of brake switch |
|
|
DETE/CANCL SW [On/Off] |
x |
Indicates condition of P position |
|
SFT PN/N SW [On/Off] |
x |
Indicates condition of P or N position |
|
UNLK SEN -DR [On/Off] |
x |
Indicates condition of door unlock sensor |
|
PUSH SW -IPDM [On/Off] |
Indicates condition of push button ignition switch received from IPDM E/R on CAN communication line |
|
|
IGN RLY1 -F/B [On/Off] |
Indicates condition of ignition relay 1 received from IPDM E/R on CAN communication line |
|
|
DETE SW -IPDM [On/Off] |
Indicates condition of detent switch received from TCM on CAN communication line |
|
|
SFT PN -IPDM [On/Off] |
Indicates condition of P or N position from TCM on CAN communication line |
|
|
SFT P -MET [On/Off] |
Indicates condition of P position from TCM on CAN communication line |
|
|
SFT N -MET [On/Off] |
Indicates condition of N position from IPDM E/R on CAN communication line |
|
|
ENGINE STATE [Stop/Start/Crank/Run] |
x |
Indicates condition of engine state from ECM on CAN communication line |
|
VEH SPEED 1 [mph/km/h] |
x |
Indicates condition of vehicle speed signal received from ABS on CAN communication line |
|
VEH SPEED 2 [mph/km/h] |
x |
Indicates condition of vehicle speed signal received from combination meter on CAN communication line |
|
DOOR STAT-DR [LOCK/READY/UNLK] |
x |
Indicates condition of driver side door status. |
|
DOOR STAT-AS [LOCK/READY/UNLK] |
x |
Indicates condition of passenger side door status. |
|
DOOR STAT-RR [LOCK/READY/UNLK] |
x |
Indicates condition of rear right side door status. |
|
DOOR STAT-RL [LOCK/READY/UNLK] |
x |
Indicates condition of rear left side door status. |
|
ID OK FLAG [Set/Reset] |
Indicates condition of Intelligent Key ID |
|
|
PRMT ENG STRT [Set/Reset] |
Indicates condition of engine start possibility from Intelligent Key |
|
|
I-KEY OK FLAG [Set/Reset] |
Indicates condition of Intelligent Key ID. |
|
|
ID AUTHENT CANCEL TIMER [under a stop] |
Indicates condition of Intelligent Key ID authentication. |
|
|
ACC BATTERY SAVER [under a stop] |
Indicates condition of battery saver. |
|
|
CRNK PRBT TMR [On/Off] |
Indicates condition of crank prohibit timer. |
|
|
AUT CRANK TMR [On/Off] |
Indicates condition of automatic engine crank timer from Intelligent Key. |
|
|
CRNK PRBT TME [sec] |
Indicates condition of engine crank prohibit time. |
|
|
AUT CRANK TMR [sec] |
Indicates condition of automatic engine crank time from Intelligent Key. |
|
|
CRANKING TME [sec] |
Indicates condition of engine cranking time from Intelligent Key. |
|
|
ST RLY -REQ |
Indicates condition of starter relay. |
|
|
IGN RLY1 -REQ |
Indicates condition of ignition 1 relay. |
|
|
IGN RLY2 -REQ |
Indicates condition of ignition 2 relay. |
|
|
DETE SW PWR [On/Off] |
Indicates condition of park position switch voltage. |
|
|
IGN RLY3 -REQ |
Indicates condition of ignition 3 relay. |
|
|
ACC RLY -REQ |
Indicates condition of ACC relay. |
|
|
PRBT ENG STRT [Set/Reset] |
Indicates condition of engine start possibility. |
|
|
PRMT RKE STRT [Set/Reset] |
Indicates condition of engine start possibility from Intelligent Key. |
|
|
TRNK/HAT MNTR [On/Off] |
Indicates condition of trunk lid. |
|
|
RKE-LOCK [On/Off] |
Indicates condition of lock signal from Intelligent Key. |
|
|
RKE-UNLOCK [On/Off] |
Indicates condition of unlock signal from Intelligent Key. |
|
|
RKE-TR/BD [On/Off] |
Indicates condition of trunk open signal from Intelligent Key. |
|
|
RKE-PANIC [On/Off] |
Indicates condition of panic signal from Intelligent Key. |
|
|
RKE-MODE CHG [On/Off] |
Indicates condition of mode change signal from Intelligent Key. |
|
|
RKE OPE COUN1 [0-19] |
x |
When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the numerical value start changing. |
|
RKE OPE COUN2 [0-19] |
x |
When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the numerical value start changing. |