Data Monitor
|
Item [Unit] |
Description |
|
|
IGN VOLT |
[V] |
Displays the ignition power supply voltage. |
|
CONTROL MODULE MALF |
[Off / On] |
Displays chassis control module malfunction. |
|
CAN DIAG STATUS |
[Off / On] |
Displays CAN network diagnosis status. |
|
VEHICLE SPEED |
[km/m] |
Displays the vehicle speed. |
|
FR WHEEL SPEED |
[rpm] |
Displays the rotational speed of front RH tire. |
|
FL WHEEL SPEED |
[rpm] |
Displays the rotational speed of front LH tire. |
|
RR WHEEL SPEED |
[rpm] |
Displays the rotational speed of rear RH tire. |
|
RL WHEEL SPEED |
[rpm] |
Displays the rotational speed of rear LH tire. |
|
STEERING ANG SENSOR |
[deg] |
Displays the steering angle from the steering angle sensor. |
|
DECEL G SENSOR |
[G] |
Displays the decel G. |
|
SIDE G SENSOR |
[G] |
Displays the side G. |
|
YAW RATE SENSOR |
[deg/s] |
Displays the yaw rate. |
|
ACCELE PEDAL POSITION |
[%] |
Displays the accelerator pedal position. |
|
THROTTLE CONTROL |
[NORMAL / INCORR / PREV / INPOSSI] |
Displays the electric throttle status. |
|
SHIFT POSITION |
[Off / P / R / N / D (A) / S / L / B / 1- 6 / M 1 -M 8 / A 1 - A 6] |
Displayed but not used. |
|
BRAKE SWITCH 2 |
[Off / On] |
Displays brake switch operating status (Off: close / On: open). |
|
BRAKE SWITCH 1 |
[Off / On] |
Displays brake switch operating status (Off: open / On: close). |
|
STOP LAMP SW |
[INACTIVE / ACTIVE] |
Displays the brake status. |
|
PRESS SENSOR |
[bar] |
Displays the brake fluid pressure. |
|
ABS |
[NORMAL / ABNOR] |
Displays ABS function status. |
|
ABS MALF |
[NORMAL / ABNOR] |
Displays ABS function status. |
|
EBD |
[NORMAL / ABNOR] |
Displays EBD function status. |
|
TCS |
[NORMAL / ABNOR] |
Displays TCS function status. |
|
TCS MALF |
[NORMAL / ABNOR] |
Displays TCS function status. |
|
VDC |
[NORMAL / ABNOR] |
Displays VDC function status. |
|
VDC MALF |
[NORMAL / ABNOR] |
Displays VDC function status. |
|
VDC OFF SWITCH |
[Off / On] |
Displays VDC OFF switch status. |
|
DRV TRQ CTRL MODE |
[INITIAL / NORMAL / STOP 1 / STOP 2 / LIMIT 1 / PROHIBI] |
Displays the status of correction to slightly increase/decrease the drive torque. |
|
DRV TRQ CTRL PERMIS 1 |
[NO PER / PERMIS] |
Displays the permission status (basic requirement) of correction to slightly increase/decrease drive torque. |
|
DRV TRQ CTRL PERMIS 2 |
[NO PER / PERMIS] |
Displays the permission status (system requirement) of correction to slightly increase/decrease drive torque. |
|
DRV TRQ CTRL STOP |
[REQ / NO REQ] |
Displays the stop request status of correction to slightly increase/decrease drive torque. |
|
DRV TRQ CTRL PROHIBIT |
[REQ / NO REQ] |
Displays the prohibition request status of correction to slightly increase/decrease drive torque. |
|
ATC SETTING |
[Off / On] |
Displays intelligent trace control status. |
|
AEB CVT PERMIT |
[Off / On] |
Displays the CVT authorized state for intelligent engine brake. |
|
AEB STATUS |
[Off / On] |
Displays the intelligent engine brake status. |
|
AEB COMMAND 1 |
[0.0000] |
Displays the relative command value of intelligent engine brake. |
|
AEB COMMAND 2 |
[0.0000] |
Displays absolute command value of intelligent engine brake. |
|
AEB SLIP RATE |
[%] |
Displays slip ratio of intelligent engine brake. |
|
AEB SETTING |
[Off / On] |
Displays intelligent engine brake control status. |