LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2019 >> Maxima SL >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System (DTC/Circuit Diagnosis) (3 Of 5) >> DTC/Circuit Diagnosis >> DTC P0441: EVAP Control System >> DTC Confirmation Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC Confirmation Procedure

  1. CHECK DTC PRIORITY 

    If DTC P0441 is displayed with other DTC such as P2122, P2123, P2127, P2128 or P2138, first perform trouble diagnosis for other DTC.

    Is applicable DTC detected?

    YES

    Perform diagnosis of applicable. Refer to DTC Index .

    NO

    GO TO 2 .

  2. INSPECTION START 

    Will CONSULT be used?

    Will CONSULT be used?

    YES

    GO TO 3.

    NO

    GO TO 7.

  3. PRECONDITIONING 

    If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

    1. Turn ignition switch OFF and wait at least 10 seconds.
    2. Turn ignition switch ON.
    3. Turn ignition switch OFF and wait at least 10 seconds.

    TESTING CONDITION:

    Always perform test at a temperature of 5 deg. C (41 deg. F) or more.

    GO TO 4.

  4. PERFORM DTC CONFIRMATION PROCEDURE-I 

    SYMBOL With CONSULT

    1. Start engine and warm it up to normal operating temperature.
    2. Turn ignition switch OFF and wait at least 10 seconds.
    3. Turn ignition switch ON.
    4. Turn ignition switch OFF and wait at least 10 seconds.
    5. Start engine and let it idle for at least 70 seconds.
    6. Select "PURG FLOW P0441" of "EVAPORATIVE SYSTEM" in "DTC WORK SUPPORT" mode with CONSULT.
    7. Touch "START".

    Is "COMPLETED" displayed on CONSULT screen?

    YES

    GO TO 6.

    NO

    GO TO 5.

  5. PERFORM DTC CONFIRMATION PROCEDURE-II 

    When the following conditions are met, "TESTING" will be displayed on the CONSULT screen. Maintain the conditions continuously until "TESTING" changes to "COMPLETED". (It will take at least 35 seconds.)

    Selector lever

    Suitable position

    VHCL SPEED SE

    32 - 120 km/h (20 - 75 mph)

    ENG SPEED

    500 - 3, 000 RPM

    B/FUEL SCHDL

    1.25 - 7.2 msec

    COOLANT TEMP/S

    More than 0 deg. C (32 deg. F)
    CAUTION: Always drive vehicle at a safe speed.

    If "TESTING" does not change for a long time, retry from step 2.

    Is "COMPLETED" displayed on CONSULT screen?

    YES

    GO TO 6.

    NO

    Perform DTC CONFIRMATION PROCEDURE again. GO TO 3.

  6. PERFORM DTC CONFIRMATION PROCEDURE-III 

    Touch "SELF-DIAG RESULTS".

    Which is displayed on CONSULT screen?

    OK-1

    To check malfunction symptom before repair: Refer to Intermittent Incident .

    OK-2

    Confirmation after repair: INSPECTION END

    NG

    Proceed to Diagnosis Procedure .

  7. PERFORM COMPONENT FUNCTION CHECK 

    SYMBOL Without CONSULT

    1. Lift up drive wheels.
    2. Start engine (VDC switch OFF) and warm it up to normal operating temperature.
    3. Turn ignition switch OFF, wait at least 10 seconds.
    4. Turn ignition switch ON.
    5. Turn ignition switch OFF, wait at least 10 seconds.
    6. Start engine and wait at least 70 seconds.
    7. Set voltmeter probes to ECM harness connector terminals under the following conditions.

      ECM

      Connector

      +

      -

      Terminal

      E10

      121

      148
    8. Check EVAP control system pressure Sensor value at idle speed and note it.
    9. Establish and maintain the following conditions for at least 1 minute.

      Air conditioner switch

      ON

      Head lamp switch

      ON

      Rear window defogger switch

      ON

      Engine speed

      Approx. 3, 000 RPM

      Gear position

      Any position other than P, N or R
    10. Verify that EVAP control system pressure Sensor value stays 0.1 V less than the value at idle speed (measured at step 6) for at least 1 second.

    Is the inspection result normal?

    YES

    To check malfunction symptom before repair: Refer to Intermittent Incident .

    YES

    Confirmation after repair: INSPECTION END

    NO

    Proceed to Diagnosis Procedure .

scientia non olet · About LEMON Manuals