CONSULT Function

APPLICATION ITEMS

CONSULT can display each diagnostic item using the diagnostic test modes as follows.

Diagnosis mode	CGW Status			Description
Diagnosis mode	Restricted Mode	Diag Test Mode	Open Mode	Description
Self Diagnostic Result	Display	Display	Display	Display non-network DTC which chassis control module (with built in steering angle sensor) memorizes
CGW Information	Display	Display	Display	Display the current CGW mode Enables CGW to switch mode
Data Monitor	Display	Display	Display	Displays chassis control module (with built in steering angle sensor) input/output data in real time
Active Test	Non-display	Display	Display	Enables an operational check of a load by transmitting a driving signal from the chassis control module (with built in steering angle sensor) to the load
ECU Identification	Display	Display	Display	Displays chassis control module (with built in steering angle sensor) part number
Re/programming, Configuration	Display	Display	Display	The vehicle specification that is written in chassis control module (with built in steering angle sensor) can be displayed or stored The vehicle specification can be written when chassis control module (with built in steering angle sensor) is replaced
Network-DTC	Display	Display	Display	Display network DTC which chassis control module (with built in steering angle sensor) memorizes when performing "Diagnosis (All System)".
CAN Diag Support Monitor*	Display	Display	Display	NOTE: The mode is indicated, but not monitored

*: Displays when performing "Diagnosis (All System)".

CGW INFORMATION

Display the diagnosis mode which a user can perform in Diag Test mode/Open Mode by switching the CGW status from Restricted mode to Diag Test Mode/Open Mode. For the method of switching CAN Gateway status, refer to CONSULT Function .

ECU IDENTIFICATION

Chassis control module (with built in steering angle sensor) part number can be read.

SELF DIAGNOSTIC RESULT

Refer to DTC Index . When "CRNT" is displayed on self-diagnosis result

The system is presently malfunctioning.

When "PAST" is displayed on self-diagnosis result

System malfunction in the past is detected, but the system is presently normal.

Freeze frame data (FFD)

When DTC is detected, a vehicle state shown below is recorded and displayed on CONSULT.

Item name	Indication/Unit	Display item
ODO/TRIP METER	km	Total mileage (Odometer value) of the moment a particular.
DTC count	count	Displays the number of times DTC is detected.
IGN VOLT	V	Displays the ignition power supply voltage.
Diag permission condition	Not permission / Permission / Not Used / Abnormal	Displays the diagnosis status.
DTC LOCAL CODE	-	Displays but not used.
VEHICLE SPEED	km/h	Displays the vehicle speed.
FR WHEEL SPEED	RPM	Displays the rotational speed of front RH tire.
FL WHEEL SPEED	RPM	Displays the rotational speed of front LH tire.
RR WHEEL SPEED	RPM	Displays the rotational speed of rear RH tire.
RL WHEEL SPEED	RPM	Displays the rotational speed of rear LH tire.
STEERING ANG SENSOR	deg	Displays the steering angle.
DECEL G SENSOR	G	Displays the decel G.
SIDE G SENSOR	G	Displays the side G.
YAW RATE SENSOR	deg/s	Displays the yaw rate.
ACCELE PEDAL POSITION	%	Displays the accelerator pedal position.
VEHICLE SPEED	km/h	Displays the vehicle speed.
Throttle control	NORMAL / INCORR / PREV / INPOSSI	Displays the electric throttle status.
SHIFT POSITION	-	Displays the shift position.
STOP LAMP SW	INACT / ACTIVE	Displays the stop lamp switch status.
PRESS SENSOR	bar	Displays the brake fluid pressure.
ABS	INACT / ACTIVE	Displays the ABS function status.
ABS MALF	Off / On	Displays the ABS malfunction status.
TCS	INACT / ACTIVE	Displays the TCS function status.
TCS MALF	Off / On	Displays the TCS malfunction status.
VDC	INACT / ACTIVE	Displays the VDC function status.
VDC MALF	Off / On	Displays the VDC malfunction status.
VDC OFF SWITCH	Off / On	Displays the VDC OFF status.
Variant code	-	Displays the vehicle specification.
AEB CVT PERMIT	Off / On	Displays the transaxle authorized state for intelligent engine brake function.

DATA MONITOR

NOTE:

The following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items.

Item [Unit]		Description
IGN VOLT	[V]	Displays the ignition power supply voltage.
CONTROL MODULE MALF	[Off / On]	Displays the chassis control module (with built in steering angle sensor) malfunction.
Diag permission condition	Not permission / Permission / Not Used / Abnormal	Displays the diagnosis status.
VEHICLE SPEED	[km/h]	Displays the vehicle speed.
FR WHEEL SPEED	[RPM]	Displays the rotational speed of front RH tire.
FL WHEEL SPEED	[RPM]	Displays the rotational speed of front LH tire.
RR WHEEL SPEED	[RPM]	Displays the rotational speed of rear RH tire.
RL WHEEL SPEED	[RPM]	Displays the rotational speed of rear LH tire.
STEERING ANG SENSOR	[deg]	Displays the steering angle.
DECEL G SENSOR	[G]	Displays the decel G.
SIDE G SENSOR	[G]	Displays the side G.
YAW RATE SENSOR	[deg/s]	Displays the yaw rate.
ACCELE PEDAL POSITION	[%]	Displays the accelerator pedal position.
Throttle control	NORMAL / INCORR / PREV / INPOSSI	Displays the electric throttle status.
SHIFT POSITION	[-]	Displays the shift position.
STOP LAMP SW	[INACT / ACTIVE]	Displays the stop lamp switch status.
PRESS SENSOR	[bar]	Displays the brake fluid pressure.
ABS	[INACT / ACTIVE]	Displays the ABS function status.
ABS MALF	[Off / On]	Displays the ABS malfunction status.
EBD	[INACT / ACTIVE]	Displays the EBD function status.
TCS	[INACT / ACTIVE]	Displays the TCS function status.
TCS MALF	[Off / On]	Displays the TCS malfunction status.
VDC	[INACT / ACTIVE]	Displays the VDC function status.
VDC MALF	[Off / On]	Displays the VDC malfunction status.
VDC OFF SWITCH	[Off / On]	Displays the VDC OFF status.
AEB CVT PERMIT	[Off / On]	Displays the transaxle authorized state for intelligent engine brake function.
AEB STATUS	[Off / On]	Displays the setting status of intelligent engine brake function.
AEB COMMAND 1	[G]	Displays the relative command value of intelligent engine brake function.
AEB COMMAND 2	[G]	Displays the relative command value of intelligent engine brake function.
AEB SLIP RATE	[%]	Displays the slip ratio of intelligent engine brake function is operating.
ABH stop hold request 1	[-]	Displays but not used.
ICC status	[-]	Displays but not used.

ACTIVE TEST

The active test is used to determine and identify details of a malfunction, based on self-diagnosis test results and data obtained in the data monitor. In response to instructions from CONSULT, instead of those from chassis control module (with built in steering angle sensor) on the vehicle, a drive signal is sent to the actuator to check its operation.

CAUTION:

Never perform active test while driving the vehicle.
Always bleed air from brake system before active test.
Never perform active test when system is malfunctioning.

NOTE:

During an active test, sometimes a chassis control warning is displayed and the master warning lamp illuminates on the information display in the combination meter; however, this is not a malfunction.

Test item	Operation	Description
BRAKE ACTUATOR 1 MODE 1	On	Controls brake fluid pressure.
BRAKE ACTUATOR 1 MODE 1	Off	Controls brake fluid pressure.
BRAKE ACTUATOR 1 MODE 2	On	Controls brake fluid pressure.
BRAKE ACTUATOR 1 MODE 2	Off	Controls brake fluid pressure.
MASTER WARNING ACTIVE	On	If touching "On" with the master warning lamp not illuminated, the master warning lamp illuminates. Stops in approximately 1 minute.
MASTER WARNING ACTIVE	Off	The master warning lamp turns OFF. (vehicle in normal state)

RE/PROGRAMMING, CONFIGURATION programing includes the following functions.

Function		Description
Re/programming, Configuration	Before replacing ECU	Allows the reading of vehicle specification (parts number) written in chassis control module (with built in steering angle sensor) to store the specification in CONSULT. Allows the saving of vehicle specification (parts number) written in chassis control module (with built in steering angle sensor) to store the specification in CONSULT.
Re/programming, Configuration	After replacing ECU	Allows the writing of vehicle information (parts number) stored in CONSULT into the chassis control module (with built in steering angle sensor).