September 30: LEMON manuals is back up on a temporary server! Slowness is possible
Basic Engine
- Adjustment - Replacement
- Removing the power train
- Fitting the power train
- Engine mounting, front right B235R, B205L/R
- Engine mounting, front left B205L/R
- Engine mounting, front left B235R
- Rear engine mounting, man.
- Rear engine mounting (aut.)
- Replacement of balancer-shaft bearings
- Engine block B235R, B205L/R
- Removal of cylinder head (in situ)
- Fitting the cylinder head (in car)
- Removal of pistons (in situ)
- Matching of pistons
- Pits on the cylinder block
- Piston rings
- Fitting pistons (in situ)
- Valve gear
- Valve-gear timing
- Valve guides
- Valve seats
- Hydraulic tappets
- Checking valve clearances
- Timing cover
- Chain tensioner, timing chain
- Checking crankshaft clearances
- Main and big-end bearing clearances
- Crankshaft seal
- Drive belt for auxiliaries
- Changing the timing chain (in situ)
- Oil sump B235R, B205L/R
- Oil pressure measurement B235R, B205L/R
- Oil filter adapter housing
- Engine oil thermostat
- Reducing valve
- Changing the balancer shaft chain, B235R, B205L/R
- Special Tools
- 30 05 469 Adapter, cooling system tester
- 30 05 758 Fluid tester
- 30 06 558 Plastigauge
- 75 19 531 Protective collar (type 10)
- 83 94 850 Lifting beam
- 78 40 622 Dial gauge
- 78 60 802 Oil pan
- 78 61 040 Valve seat cutter, 11° and 45° "O SLASH"34.5 mm
- 78 61 065 T-wrench
- 78 62 287 Piston fitting tool
- 78 74 878 Floor stand
- 82 93 094 Sleeve 27 mm
- 82 93 128 Template 1/2"
- 83 90 130 Spring balance
- 83 90 270 Sliding hammer
- 83 90 478 Axle
- 83 90 494 Valve guide tool
- 83 90 858 Journal
- 83 91 401 Magnetic tool
- 83 92 409 Lifting sling
- 83 93 332 Wrench, small oil filter
- 83 93 472 Wrench, knock sensor and oil pressure switch
- 83 93 746 Protective collar
- 83 93 761 Valve spring tool
- 83 93 779 Tappets
- 83 93 787 Valve stand
- 83 93 795 Fixture, cylinder head
- 83 93 811 Pull rod
- 83 93 829 Sleeve
- 83 93 837 Stop
- 83 93 845 Nut
- 83 93 852 Pressure measuring equipment, fuel and oil pressure
- 83 93 928 Guide spindle, "OSLASH"7 mm
- 83 93 936 Valve seat cutters, 60°
- 83 94 157 Pliers, valve guide seal
- 83 94 165 Fitting kit, fitting/removing valve springs
- 83 94 173 Compressed air adapter for spark plug hole
- 83 94 181 Removal tool
- 83 94 207 Fitting tool
- 83 94 470 Balancer shaft bearing press
- 83 94 520 Wrench, lock nut
- 83 94 595 Plug, turbo hose
- 83 94 637 Removal tool
- 83 94 645 Fitting tool
- 83 94 652 Fixture
- 83 94 660 Chain lock
- 83 94 678 Timing chain removal kit, 16 valve
- 83 94 736 Guide pins, intake manifold
- 83 94 744 Adapter, fuel pressure testing
- 83 94 868 Flywheel locking attachment
- 83 94 876 Fitting tool, crankshaft seal
- 83 94 884 Fitting tool, crankshaft seal
- 83 93 944 Reamer, "OSLASH"7 mm, valve guide
- 83 95 071 Fitting tool, valve stem gasket
- 83 95 089 Valve guide reamer, 6mm
- 83 95 105 Valve seat cutter, 70° "O SLASH" 31 mm
- 83 95 147 Adapter
- 83 95 212 Strap
- 83 95 220 Engine holder, 4-cyl.
- 83 95 238 Wedge
- 83 95 246 Valve spring depressor
- 83 95 261 Fuel line tool
- 83 95 287 Holder
- 83 95 311 Trolley lift
- 83 95 345 Adapter, compression pressure sensor
- 83 95 485 Spark plug socket assembly with locating sleeves
- 83 95 501 Air nipple
- 83 95 527 Guide and plastic screw
- 83 95 535 Hook with wing nut
- 85 80 045 Adjustment tool, spark plug, 0.6 mm
- 86 12 509 Floor stand base
- 87 90 727 Bracket, dial gauge
- 87 91 857 Contact points
- 87 92 194 Dial gauge kit
- 87 92 244 Plugs, F25 drive shaft holes
- 87 92 335 Locking pin
- 87 92 442 Lifting cable
- 87 92 616 Removing tool, drive shafts
- 87 92 665 Protective plug, drive shaft hole
- 89 96 696 Puller
- Technical Data
- Technical Description