LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Saturn >> 2006 >> Ion Red Line >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls - DTC P023A To DTC P0131 >> DTC P0068 >> Test Description
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. 6:  This step will determine if the SCIP sensor voltage is within the proper range with the key ON, engine OFF.
  2. 7:  This step will determine if the sensor responds properly to the change in super charger inlet pressure.
  3. 10:  When the PCM detects a condition within the ETC system, other DTCs may set due to the many redundant tests run continuously on this system. Locating and repairing one individual condition may correct more than one DTC. Keep this in mind when reviewing captured DTC info.
DTC P0068

Step Action Values Yes No
Schematic Reference: Engine Controls Schematics
Connector End View Reference: Engine Controls Connector End Views or Powertrain Control Module (PCM) Connector End Views
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle
2 Are DTCs P0101, P0120, P0220, P1516, P2101, P2119, P2135 or P2176 also set? - Go to Diagnostic Trouble Code (DTC) List - Vehicle Go to Step 3 
3
  1. Observe the Freeze Frame/Failure Records for this DTC.
  2. Turn OFF the ignition.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?		 - Go to Step 4  Go to Testing for Intermittent Conditions and Poor Connections
4 Inspect for the following conditions:
  • Vacuum hoses for splits, kinks, and proper connections as shown on the Vehicle Emission Control Information label-Inspect thoroughly for any type of leak or restriction.
  • Air leaks at throttle body mounting area and intake manifold sealing surfaces

Did you find and correct the condition?		 - Go to Step 10  Go to Step 5 
5
    IMPORTANT: The Altitude vs. Barometric Pressure (BARO) table indicates a pressure range for a given altitude under normal weather conditions. Weather conditions consisting of very low or very high pressure and/or temperature may cause a reading to be slightly out of range.
  1. Accurately determine the altitude.
  2. Turn ON the ignition, with the engine OFF.
  3. Observe the BARO Sensor kPa parameter with a scan tool.
  4. The BARO sensor pressure should be within the specified range for your altitude. Refer to Altitude vs Barometric Pressure .
Is the BARO sensor pressure within the specified range as indicated on the Altitude vs. Barometric pressure table?		 - Go to Step 6  Go to DTC P2228 or DTC P2229
6 
  1. Allow the engine to reach operating temperature.
  2. Turn OFF the engine.
  3. Turn ON the ignition, with the engine OFF.
  4. Observe the super charger inlet pressure (SCIP) sensor voltage parameter with a scan tool.
Is the SCIP sensor voltage within the specified range?		 2.2-2.4 V Go to Step 7  Go to DTC P1182
7 
  1. Idle the engine.
  2. Observe the SCIP sensor kPa parameter with a scan tool.
  3. Increase the engine speed slowly and then back to idle.
Does the SCIP sensor kPa change smoothly and gradually as engine speed is increased and returned to idle?		 - Go to Step 8  Go to DTC P1182
8
  1. Idle the engine.
  2. Take a snapshot of the Engine Data List while performing the following action:
    • Increase the engine speed slowly to 3,000 RPM, then back to idle.
    • Exit from the snapshot and review the data.
    • Observe the MAF g/s sensor parameter frame by frame with a scan tool.

      Refer to Scan Tool Snapshot Procedure .

Does the MAF sensor g/s change smoothly and gradually as the engine speed is increased and is returned to idle?		 - Go to Step 9  Go to DTC P0101 
9
    CAUTION: Turn OFF the ignition before inserting fingers into the throttle bore. Unexpected movement of the throttle blade could cause personal injury.
  1. Inspect the throttle body for the following conditions while modulating the throttle using the scan tool:
    • Loose or damaged throttle blade
    • Broken throttle shaft
    • Drive mechanism damage
  2. If any of these conditions exist, replace the throttle body assembly. Refer to Throttle Body Assembly Replacement .
Did you find and correct the condition?		 - Go to Step 10  Go to Testing for Intermittent Conditions and Poor Connections
10 
  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?		 - Go to Step 2  Go to Step 11 
11 Observe the Capture Info with a scan tool.
Are there any DTCs that have not been diagnosed?		 - Go to Diagnostic Trouble Code (DTC) List - Vehicle System OK
scientia non olet · About LEMON Manuals