Read Current Data For Engine (OBD Mode)

On the «Main Menu» display screen, select {Each System Check}.
On the «System Selection Menu» display screen, select {Engine Control System}.
Select the [OK] after the information of engine type has been displayed.
On the «Engine Diagnosis» display screen, select {OBD System}.
On the «OBD system» display screen, select the {Current Data Display/Save}.
On the «Data Display Menu» display screen, select the {Data Display}.
Using the scroll key, scroll the display screen up or down until the desired data is shown.

A list of the support data is shown in the following table.

CURRENT DATA CHART FOR ENGINE (OBD MODE)

Remarks	Display	Unit of measure	Note (at idling)
Number of diagnosis code	Number of Diag. Code:	-	-
Condition of malfunction indicator light	Ml (MIL)	-	ON or OFF
Misfire monitoring	Misfire Monitoring	Supp	YES or NO
Misfire monitoring	Misfire Monitoring	Rdy	YES or NO
Fuel system diagnosis	Fuel system monitoring	Supp	YES or NO
Fuel system diagnosis	Fuel system monitoring	Rdy	YES or NO
Component monitoring	Component monitoring	Supp	YES or NO
Component monitoring	Component monitoring	Rdy	YES or NO
Catalyst diagnosis	Catalyst Diagnosis	Supp	YES or NO
Catalyst diagnosis	Catalyst Diagnosis	Rdy	YES or NO
Heated catalyst diagnosis	Heated catalyst	Supp	N/A
Heated catalyst diagnosis	Heated catalyst	Rdy	N/A
Evaporative purge system diagnosis	Evaporative purge system	Supp	YES or NO
Evaporative purge system diagnosis	Evaporative purge system	Rdy	YES or NO
Secondary air system	Secondary air system	Supp	YES or NO
Secondary air system	Secondary air system	Rdy	YES or NO
A/C system refrigerant diagnosis	A/C system refrigerant	Supp	N/A
A/C system refrigerant diagnosis	A/C system refrigerant	Rdy	N/A
Oxygen sensor diagnosis	Oxygen sensor	Supp	YES or NO
Oxygen sensor diagnosis	Oxygen sensor	Rdy	YES or NO
Oxygen heater diagnosis	O2 Heater Diagnosis	Supp	YES or NO
Oxygen heater diagnosis	O2 Heater Diagnosis	Rdy	YES or NO
EGR diagnosis	EGR system	Supp	N/A
EGR diagnosis	EGR system	Rdy	N/A
Air fuel ratio control system for bank 1	Fuel system for Bank1	-	Normal CLOSE
Engine load data	Engine Load	%	21.0%
Engine coolant temperature signal	Coolant Temp.	°C or °F	+91°Cor196°F
Short term fuel trim by front oxygen (A/F) sensor	Short term fuel trim B1	%	0.8%
Long term fuel trim by front oxygen (A/F) sensor	Long term fuel trim B1	%	3.9%
Intake manifold absolute pressure signal	Mani. Absolute Pressure	mmHg, kPa, inHg or psig	233 mmHg, 31 kPa, 9.2 inHg or 4.5 psig
Engine speed signal	Engine Speed	rpm	700 rpm
Vehicle speed signal	Vehicle Speed	km/h or MPH	0 km/h or 0 MPH
#1 Cylinder ignition timing	Ignition timing adv. #1	0	+16.5°
Intake air temperature signal	Intake Air Temp.	°C or °F	54°C or 129°F
Amount of intake air	Mass Air Flow	g/s or lb/m	2.8 g/s or 0.37 lb/m
Throttle position signal	Throttle Opening Angle	%	13%
Secondary air system	Secondary air system	-	Stop
Oxygen sensor #11	Oxygen Sensor #11	-	Support
Rear oxygen sensor output signal	Oxygen Sensor #12	-	Support
Oxygen sensor #12	Oxygen Sensor #12	V	0.1-0.7 V
Air fuel ratio correction by rear oxygen sensor	Short term fuel trim #12	%	+0.0%
On-board diagnostic system	OBD System	-	CARB-OBD2
A/F lambda signal	A/F sensor #11	-	1.001
A/F sensor output signal	A/F sensor #11	V	2.805 V
A/F lambda signal #11	A/F sensor #11	-	0.999
A/F sensor current #11	A/F sensor #11	mA	0.02 mA

NOTE: For detailed operation procedure, refer to the " SUBARU SELECT MONITOR OPERATION MANUAL ".