Adjusting Parts
WARNING: This page is about a different car, the 2011 Subaru Tribeca. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATION
| Drive pinion bearing preload | Measure with spring scale. (Measured at the companion flange bolt hole) | N (kgf, lb) | 12.7 - 32.2 (1.3 - 3.3, 2.9 - 7.2) |
| Measure with torque wrench | N.m (kgf-m, ft-lb) | 0.48 - 1.22 (0.05 - 0.12, 0.35 - 0.90) | |
| Preload adjusting spacer | Part No. | Length mm (in) | |
| 31454AA250 | 51.05 (2.010) | ||
| 31454AA260 | 51.25 (2.018) | ||
| 31454AA270 | 51.35 (2.022) | ||
| 31454AA280 | 51.45 (2.026) | ||
| 31454AA290 | 51.55 (2.030) | ||
| 31454AA300 | 51.65 (2.033) | ||
| 31454AA310 | 51.75 (2.037) | ||
| 31454AA320 | 51.85 (2.041) | ||
| 31454AA330 | 52.05 (2.049) | ||
THICKNESS SPECIFICATION
| Preload adjusting washer | Part No. | Thickness mm (in) |
| 38336AA430 | 1.500 (0.0591) | |
| 38336AA440 | 1.513 (0.0596) | |
| 38336AA450 | 1.525 (0.0600) | |
| 38336AA460 | 1.538 (0.0606) | |
| 38336AA470 | 1.550 (0.0610) | |
| 38336AA480 | 1.563 (0.0615) | |
| 38336AA490 | 1.575 (0.0620) | |
| 38336AA500 | 1.588 (0.0625) | |
| 38336AA510 | 1.600 (0.0630) | |
| 38336AA520 | 1.613 (0.0635) | |
| 38336AA530 | 1.625 (0.0640) | |
| 38336AA540 | 1.638 (0.0645) | |
| 38336AA550 | 1.650 (0.0650) | |
| 38336AA560 | 1.663 (0.0655) | |
| 38336AA570 | 1.675 (0.0659) | |
| 38336AA580 | 1.688 (0.0665) | |
| 38336AA590 | 1.700 (0.0669) | |
| 38336AA600 | 1.713 (0.0674) | |
| 38336AA610 | 1.725 (0.0679) | |
| 38336AA620 | 1.738 (0.0684) | |
| 38336AA630 | 1.750 (0.0689) | |
| 38336AA640 | 1.763 (0.0694) | |
| 38336AA650 | 1.775 (0.0699) | |
| Pinion height adjusting washer | Part No. | Thickness mm (in) |
| 32295AA350 | 0.150 (0.0059) | |
| 32295AA360 | 0.175 (0.0069) | |
| 32295AA370 | 0.200 (0.0079) | |
| 32295AA380 | 0.225 (0.0089) | |
| 32295AA390 | 0.250 (0.0098) | |
| 32295AA400 | 0.275 (0.0108) | |
| Hypoid driven gear to drive pinion backlash | Limit mm (in) | 0.10 - 0.15 (0.004 - 0.006) |