EyeSight Temporary Code(s) Display: List: Notes
- List of EyeSight temporary stop code
| EyeSight pause code | Item | Contents of diagnosis | Reference |
|---|---|---|---|
| E5 | Stereo Camera Temporary Stop | The operation stopped temporarily due to vertical deviation of the optical axis of the stereo camera. (During CRUISE MAIN ON, "Temporary stop" is displayed in the multi-information display.) | Perform inspection concerning the item for E5 of the "CHECK LIST (CAMERA TEMPORARY STOP)". <Ref. to
CHECK LIST (CAMERA TEMPORARY STOP) , LIST, EyeSight Temporary Code(s) Display.> This code may be displayed when the rear of the vehicle is lowered by the overload. When the failure is resolved, and the operation returns from the temporary stop status after driving for a while, it is normal. If this code is displayed in an ordinary use under which the vehicle is not tilted, readjust the stereo camera. <Ref. to PROCEDURE , Camera Adjustment, Inspection.> If the same cancel code is still detected after readjustment, replace the stereo camera. <Ref. to REMOVAL , Stereo Camera.> |
| CC | Temporary stop was performed due to the bad weather, backlight, fogged window or dirty window interfering with the recognition function of the stereo camera. And this code may be displayed also when the front of the camera is blocked by the hand or when it is very dark around the vehicle or when the vehicle is surrounded by the blanket of snow and nothing can be seen from the stereo camera. (During CRUISE MAIN ON, "Temporary stop Camera view defectiveness" is displayed in the multi-information display.) | Investigate the following items No. 1 and No. 2, and check that the possible cause of the temporary stop is applied either to No. 1 or No. 2.
When the causes of the temporary stop for No. 1 and No. 2 correspond, drive the vehicle for a while after the cause of the temporary stop has been eliminated. If the operation returns from the temporary stop status, it is normal. (However, when the temporary stop takes place and is cancelled repeatedly, the temporary stop status is kept for a while to delay the return of the operation, which prevents the irritation.) When this is not the case, check the stereo camera and its periphery. <Ref. to WINDSHIELD GLASS AND DASHBOARD , INSPECTION, General Description.> <Ref. to FRONT WIPER , INSPECTION, General Description.> <Ref. to STEREO CAMERA , INSPECTION, General Description.> |
|
| CD | |||
| CE | The temperature of the stereo camera became excessively high or low, and the operation stopped temporarily. (During CRUISE MAIN ON, "Temporary stop Camera temperature range outside" is displayed in the multi-information display.) | Perform inspection concerning the item for CE of the "CHECK LIST (CAMERA TEMPORARY STOP)". <Ref. to
CHECK LIST (CAMERA TEMPORARY STOP) , LIST, EyeSight Temporary Code(s) Display.> When the operation returns from the temporary stop status after the failure is resolved, it is normal. When the operation does not return from the temporary status even if driving the vehicle for a while after the failure has been resolved, replace the stereo camera. <Ref. to REMOVAL , Stereo Camera.> |
|
| 33 | Detected when engine speed is 300 rpm or less. (Not detected at an initial ignition switch ON.) (During CRUISE MAIN ON, "Temporary stop" is displayed in the multi-information display.) |
Detected when the engine speed drops below 300 rpm after the engine has started once. If the same EyeSight temporary stop code is detected again when the engine is restarted, check the ECM. <Ref. to PROCEDURE , Basic Diagnostic Procedure.> |
|
| C0 | Pre-Collision Second Braking Activation | The operation stopped temporarily because the pre-collision secondary brake operated three times between engine starting and stopping. (This is not a normal driving operation, or the system may be malfunctioning.) (During CRUISE MAIN ON, "Temporary stop" is displayed in the multi-information display.) | This code may be displayed when the pre-collision brake is operated intentionally. Turn the ignition switch to OFF, and restart after a while. If the operation returns from the temporary stop status, it is normal. When temporary stop status continues with a code other than C0 after restart, perform diagnosis according to the code. When temporary stop status continues with the code of C0 after restart, the stereo camera may be malfunctioning. Replace the stereo camera. <Ref. to REMOVAL , Stereo Camera.> |
| A0 | CAN Diagnosis | The voltage dropped below 10 V immediately after IGN ON. (During CRUISE MAIN ON, "Temporary stop" is displayed in the multi-information display.) | This code may be displayed when the engine is not started for a while with the ignition switch ON and when the engine has started after that. This is a normal operation. If this is not the case, the supply voltage may be malfunctioning. <Ref. to DTC B2814 POWER SUPPLY LOW VOLTAGE , Diagnostic Procedure with Diagnostic Trouble Code (DTC).> |
| A1 | ECM Reprogramming | The operation stopped temporarily because the control module (CM) is being reprogrammed. (During CRUISE MAIN ON, "Temporary stop" is displayed in the multi-information display.) | After the completion of the reprogramming operation, turn the ignition to OFF and restart. If the operation returns from the temporary stop status, it is normal. |
| F9 | EPS Input Control Suspended | The operation stopped temporarily because an assist limitation (overheat prevention control) was operated in order to prevent the electric power steering malfunction due to overheat. | This code may be displayed when the steering wheel is operated repeatedly while the vehicle is stopped or running in very low speed. After stopping the engine, leave the vehicle for approximately 30 minutes to cool down, and restart the engine. If the operation returns from the temporary stop status, it is normal. |
| The operation stopped temporarily because of an electric power steering voltage decrease. | This code may be displayed when battery power is low. Replace or charge the battery, and restart the engine. If the operation returns from the temporary stop status, it is normal. | ||
| The operation stopped temporarily because of an electric power steering bus off. | Electric power steering detected a failure and was disconnected from CAN line. | ||
| FA | EPS Input Control Suspended | The operation stopped temporarily because the center point of steering angle sensor deviated. | This code may be displayed when the center point of steering angle sensor deviates when removing and installing the steering etc. If the system returns from the temporary stop status after inspecting/adjusting the center point and driving the vehicle for a while, it is normal. |
| The operation stopped temporarily because there was an excessive deviation in the alignment. (During CRUISE MAIN ON, "Temporary stop" is displayed in the multi-information display.) | This code may be displayed when vehicle underbody parts are damaged by a car accident etc, or when the underbody parts are replaced. If the system returns from the temporary stop status after replacing the parts and driving the vehicle for a while, it is normal. |
NOTE:
*: Automatic adjustment by driving
- Drive vehicle at a speed from 45 km/h (25 MPH) to 100 km/h (62 MPH).
- Drive the vehicle so that the distance from the preceding vehicle is 40 m (131 ft) or more or there are no preceding vehicles. (To recognize both right and left white lines)
- Drive the vehicle on a road where right and left white lines are clearly recognized and there are many straight segments. (If there are no corresponding general roads, drive the vehicle on a limited highway.)
- Display the current data «Lane recognition status» with Subaru Select Monitor, and then drive the vehicle on a road where Subaru Select Monitor indicates 03 or 05 (the system recognizes both white lines). <Ref. to
STEREO CAMERA , OPERATION, Read Current Data.>CAUTION: When performing operations by one person, use Save of the current data for the Subaru Select Monitor to save «Lane recognition status». Check the saved data after stopping the vehicle.