Specifications Index
COROLLA SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT OIL & REFRIGERANT SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Shaft/Bearing Lock Nut/Drive Axle Nut (Front) | 159 ft.lbs (216 N.m) | ||
| Axle Hub-To-Axle Carrier Bolts (Rear) | 59 ft.lbs (80 N.m) | ||
| Battery | CAPACITIES - 1.6L CAPACITIES - 1.8L |
||
| Brakes | |||
| Bleeding Sequence | BLEEDING BRAKE SYSTEM | ||
| Disc Brakes | DISC & DRUM BRAKE SPECIFICATIONS | ||
| Drum Brakes | DISC & DRUM BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | ON-VEHICLE TESTING | ||
| Torque | OVERHAUL | ||
| Drive Belts | |||
| Adjustment | BELT ADJUSTMENT | ||
| Belt Routing | BELT ROUTING | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM SPECIFICATIONS | ||
| Radiator Cap Pressure | 10.7-14.9 psi Minimum opening pressure is 8.5 psi |
||
| Thermostat R & I | n/a | ||
| Water Pump R & I | WATER PUMP - 1.6L WATER PUMP - 1.8L |
||
| Engine Mechanical | |||
| 1.6L | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | Oil pressure should be at least 4.3 psi (0.3 kg/cm2 ) at idle and 36-71 psi (2.5-5.0 kg/cm2 ) at 3000 RPM | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 1.8L | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | Oil pressure should be at least 4.3 psi (0.3 kg/cm2 ) at idle and 36-71 psi (2.5-5.0 kg/cm2 ) at 3000 RPM | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. | ||
| Flywheel/Flex Plate (Drive Plate) Torque | |||
| A/T | 47 ft.lbs (64 N.m) | ||
| M/T | 58 ft.lbs (79 N.m) | ||
| Fuel System | |||
| Pressure Specification | FUEL PRESSURE | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE | ||
| Fuel Filter Location | |||
| In Tank Type | FUEL SYSTEM - 1.6L FUEL SYSTEM - 1.8L |
||
| Ignition | |||
| 1.6L | |||
| Firing Order & Cylinder Identification | FIRING ORDER | ||
| Ignition Wires (Resistance) | HIGH TENSION WIRE RESISTANCE | ||
| Ignition Wires (Routing) | IGNITION SYSTEM | ||
| 1.8L | |||
| Firing Order & Cylinder Identification | FIRING ORDER | ||
| Ignition Wires (Resistance) | HIGH TENSION WIRE RESISTANCE | ||
| Ignition Wires (Routing) | IGNITION SYSTEM | ||
| Spark Plug | |||
| Type | NGK No. BKR5EYA NIPPONDENSO No. K16R-U |
||
| Gap | 0.031 In. (0.80 mm) | ||
| Torque | 13 ft.lbs (18 N.m) | ||
| Starting | |||
| Starter | STARTER SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 76 ft.lbs (103 N.m) | ||