Specifications Index
CELICA SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Shaft/Bearing Lock Nut (Front) | 159 ft.lbs (216 N.m) | ||
| Axle Hub-To-Axle Carrier Bolts (Rear) | 41 ft.lbs (56 N.m) | ||
| Battery | NA | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING BRAKE SYSTEM | ||
| Disc Brakes | DISC & DRUM BRAKE SPECIFICATIONS | ||
| Drum Brakes | DISC & DRUM BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | ON-VEHICLE TESTING | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | DRIVE BELT TENSION SPECIFICATIONS | ||
| Belt Routing | DRIVE BELT ROUTING | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM SPECIFICATIONS | ||
| Radiator Cap Pressure | 13.5-17.8 psi Minimum opening pressure is 11.4 psi |
||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | |||
| 1.8L (1ZZ-FE) | At normal operating temperature, oil pressure should be at least 4.3 psi (0.3 kg/cm2
) at idle. 43-78 psi (3.0-5.5 kg/cm2 ) at 3000 RPM. |
||
| 1.8L (2ZZ-GE) | At normal operating temperature, oil pressure should be at least 5.7 psi (0.4 kg/cm2
) at idle. 43-78 psi (3.0-5.5 kg/cm2 ) at 3000 RPM. |
||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. | ||
| Flywheel/Flex Plate (Drive Plate) Torque | |||
| A/T | 65 ft.lbs (88 N.m). | ||
| M/T | Step 1) 36 ft.lbs (49 N.m) Step 2) additional 90 degree turn |
||
| Fuel System | |||
| Pressure Specification | 44-50 (3.1-3.5) | ||
| Fuel Pressure Test Procedure | CELICA, COROLLA & ECHO | ||
| Fuel Filter Location | |||
| FUEL FILTER (CNG) | |||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | HIGH TENSION WIRE RESISTANCE | ||
| Ignition Wires (Routing) | NA | ||
| Spark Plug | |||
| Type | |||
| 1.8L (1ZZ-FE) | NGK No. IFR5A11 DENSO No. SK16R11 |
||
| 1.8L (2ZZ-GE) | NGK No. IFR6A11 DENSO No. SK20R11 |
||
| Gap | .043 (1.10) | ||
| Torque | 13 ft.lbs (18 N.m) | ||
| Starting | |||
| Starter | STARTER SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 76 ft.lbs (103 N.m) | ||