CONSULT Reference Value in Data Monitor Mode

WARNING: This page is about a different car, the 2013 Nissan Armada. However, it is still accessible from the selected car via links, so may be relevant.

NOTE:

The following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items.
Numerical values in the following table are reference values.
These values are input/output values that ECM receives/transmits and may differ from actual operations.

Example:

The ignition timing shown by the timing light may differ from the ignition timing displayed on the data monitor. This occurs because the timing light shows a value calculated by ECM according to signals received from the cam shaft position sensor and other sensors related to ignition timing.

For outlines of following items, refer to "CONSULT FUNCTION ".

MONITOR ITEM

CONDITION

SPECIFICATION

ENG SPEED

Run engine and compare CONSULT value with the tachometer indication.

Almost the same speed as the tachometer indication.

MAS A/F SE-B1

See TROUBLE DIAGNOSIS - SPECIFICATION VALUE .

B/FUEL SCHDL

See TROUBLE DIAGNOSIS - SPECIFICATION VALUE .

A/F ALPHA-B1
A/F ALPHA-B2

See TROUBLE DIAGNOSIS - SPECIFICATION VALUE .

COOLANT TEMP/S

Engine: After warming up

More than 70°C (158°F)

A/F SEN1 (B1)

Engine: After warming up

Maintaining engine speed at 2, 000 RPM

Fluctuates around 2.2 V

HO2S2 (B1)
HO2S2 (B2)

Revving engine from idle to 3, 000 RPM quickly after the following conditions are met.
- Engine: After warming up
- Keeping engine speed between 3, 500 and 4, 000 RPM for 1 minute and at idle for 1 minute under no load

0 - 0.3V ←→ Approx. 0.6 - 1.0V

HO2S2 MNTR (B1)
HO2S2 MNTR (B2)

Revving engine from idle to 3, 000 RPM quickly after the following conditions are met.
- Engine: After warming-up
- Keeping engine speed between 3, 500 and 4, 000 RPM for 1 minute and at idle for 1 minute under no load

LEAN ←→ RICH

VHCL SPEED SE

Turn drive wheels and compare CONSULT value with the speedometer indication.

Almost the same speed as the speedometer indication

BATTERY VOLT

Ignition switch: ON (Engine stopped)

11 - 14V

ACCEL SEN 1

Ignition switch: ON (Engine stopped)

Accelerator pedal: Fully released

0.5 - 1.0V

Accelerator pedal: Fully depressed

4.2 - 4.8V

ACCEL SEN 2⁽¹⁾

Ignition switch: ON (Engine stopped)

Accelerator pedal: Fully released

0.5 - 1.0V

Accelerator pedal: Fully depressed

4.2 - 4.8V

TP SEN 1-B1
TP SEN 2-B1

Ignition switch: ON (Engine stopped)
Selector lever: D

Accelerator pedal: Fully released

More than 0.36V

Accelerator pedal: Fully depressed

Less than 4.75V

FUEL T/TMP SE

Ignition switch: ON

Indicates fuel tank temperature.

EVAP SYS PRES

Ignition switch: ON

Approx. 1.8 - 4.8V

FUEL LEVEL SE

Ignition switch: ON

Depending on fuel level of fuel tank.

START SIGNAL

Ignition switch: ON → START → ON

OFF → ON → OFF

CLSD THL POS

Ignition switch: ON (Engine stopped)

Accelerator pedal: Fully released

Accelerator pedal: Slightly depressed

OFF

AIR COND SIG

Engine: After warming up, idle the engine

Air conditioner switch: OFF

OFF

Air conditioner switch: ON (Compressor: Operates)

PW/ST SIGNAL

Engine: After warming up, idle the engine

Steering wheel: Not being turned (Forward direction)

OFF

Steering wheel: Being turned

LOAD SIGNAL

Ignition switch: ON

Rear window defogger switch is ON and/or lighting switch is in 2nd.

Rear window defogger switch is OFF and lighting switch is OFF.

OFF

IGNITION SW

Ignition switch: ON → OFF → ON

ON → OFF → ON

HEATER FAN SW

Engine: After warming up, idle the engine

Heater fan control switch: ON

Heater fan control switch: OFF

OFF

BRAKE SW

Ignition switch: ON

Brake pedal: Fully released

OFF

Brake pedal: Slightly depressed

INJ PULSE-B1
INJ PULSE-B2

Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load

Idle

2.0 - 2.8 msec

2, 000 RPM

1.9 - 2.9 msec

IGN TIMING

Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load

Idle

10° - 20° BTDC

2, 000 RPM

25° - 45° BTDC

CAL/LD VALUE

Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load

Idle

14% - 33%

2, 500 RPM

12% - 25%

MASS AIRFLOW

Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load

Idle

3.0 - 9.0 g/s

2, 500 RPM

9.0 - 28.0 g/s

PURG VOL C/V

Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load

Idle (Accelerator pedal: Not depressed even slightly, after engine starting.)

2, 000 RPM

INT/V TIM(B1)
INT/V TIM(B2)

Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load

Idle

-5)° - (+5)°CA

2, 000 RPM

Approx. 0° - 20°CA

INT/V SOL (B1)
INT/V SOL (B2)

Engine: After warming up
Selector lever: P or N
Air conditioner switch: OFF
No load

Idle

0% - 2%

2, 000 RPM

Approx. 25% - 50%

AIR COND RLY

Engine: After warming up, idle the engine

Air conditioner switch: OFF

OFF

Air conditioner switch: ON (Compressor: Operates)

FUEL PUMP RLY

For 1 second after turning ignition switch ON
Engine running or cranking

Except above conditions

OFF

FPCM⁽²⁾

Engine: Cranking

Engine: Idle
Engine coolant temperature: More than 10°C (50°F)

LOW

VENT CONT/V

Ignition switch: ON

OFF

THRTL RELAY

Ignition switch: ON

A/F S1 HTR(B2)

Engine: After warming up, idle the engine

4 - 100%

COOLING FAN

Engine: After warming up, idle the engine
Air conditioner switch: OFF

Engine coolant temperature: 99°C (210°F) or less

OFF

Engine coolant temperature: 100°C (212°F) or more

HO2S2 HTR (B1)
HO2S2 HTR (B2)

Engine speed: Below 3, 600 RPM after the following conditions are met.
- Engine: After warming up
- Keeping the engine speed between 3, 500 and 4, 000 RPM for 1 minute and at idle for 1 minute under no load

Engine speed: Above 3, 600 RPM

OFF

ALT DUTY SIG

Power generation voltage variable control: Operating

Power generation voltage variable control: Not operating

OFF

I/P PULLY SPD

Vehicle speed: More than 20 km/h (12 MPH)

Almost the same speed as the tachometer indication

VEHICLE SPEED

Turn drive wheels and compare CONSULT value with the speedometer indication.

Almost the same speed as the speedometer indication

IDL A/V LEARN

Engine: Running

Idle air volume learning has not been performed yet.

YET

Idle air volume learning has already been performed successfully.

CMPLT

TRVL AFTER MIL

Ignition switch: ON

Vehicle has traveled after MIL has turned ON.

0 - 65, 535 km
(0 - 40, 723 mile)

A/F S1 HTR(B1)

Engine: After warming up, idle the engine

4 - 100%

VHCL SPEED SE

Turn drive wheels and compare CONSULT value with the speedometer indication.

Almost the same speed as the speedometer indication

SET VHCL SPD

Engine: Running

ASCD: Operating.

The preset vehicle speed is displayed.

MAIN SW

Ignition switch: ON

MAIN switch: Pressed

MAIN switch: Released

OFF

CANCEL SW

Ignition switch: ON

CANCEL switch: Pressed

CANCEL switch: Released

OFF

RESUME/ACC SW

Ignition switch: ON

RESUME/ACCELERATE switch: Pressed

RESUME/ACCELERATE switch: Released

OFF

SET SW

Ignition switch: ON

SET/COAST switch: Pressed

SET/COAST switch: Released

OFF

BRAKE SW1

Ignition switch: ON

Brake pedal: Fully released

Brake pedal: Slightly depressed

OFF

BRAKE SW2

Ignition switch: ON

Brake pedal: Fully released

OFF

Brake pedal: Slightly depressed

VHCL SPD CUT

Ignition switch: ON

NON

LO SPEED CUT

Ignition switch: ON

NON

AT OD MONITOR

Ignition switch: ON

OFF

AT OD CANCEL

Ignition switch: ON

OFF

CRUISE LAMP

Ignition switch: ON

MAIN switch: Pressed at the 1st time → at the 2nd time

ON → OFF

SET LAMP

MAIN switch: ON
Vehicle speed: Between 40 km/h (25 MPH) and 144 km/h (89 MPH)

ASCD: Operating

ASCD: Not operating

OFF

ETHANOL M/R⁽²⁾

Ignition switch: ON

0 - 85%

ALT DUTY

Engine: Idle

0 - 80%

BAT CUR SEN

Engine speed: Idle
Battery: Fully charged⁽³⁾
Selector lever: P or N
Air conditioner switch: OFF
No load

Approx. 2, 600 - 3, 500mV

A/F ADJ-B1

Engine: Running

(-0.330) - (+0.330)

A/F ADJ-B2

Engine: Running

(-0.330) - (+0.330)

P/N POSI SW

Ignition switch: ON

Selector lever: P or N

Selector lever: Except above

OFF

INT/A TEMP SE

Ignition switch: ON

Indicates intake air temperature.

AC PRESS SEN

Engine: Idle
Both A/C switch and blower fan switch: ON (Compressor operates.)

1.0 - 4.0V

A/F SEN1 (B2)

Engine: After warming up

Maintaining engine speed at 2, 000 RPM

Fluctuates around 2.2 V

VTC DTY EX B2

FPCM DR VOLT

Not used.

THRTL STK CNT B1

NOTE: The item is indicated, but not used.

HO2 S2 DIAG2 (B1)

DTC P0139 self-diagnosis (slow response) is incomplete.

INCMP

DTC P0139 self-diagnosis (slow response) is complete.

CMPLT

HO2 S2 DIAG2 (B2)

DTC P0159 self-diagnosis (slow response) is incomplete.

INCMP

DTC P0159 self-diagnosis (slow response) is complete.

CMPLT

A/F SEN1 DIAG2 (B1)

NOTE: The item is indicated, but not used.

A/F SEN1 DIAG2 (B2)

NOTE: The item is indicated, but not used.

EVAP LEAK DIAG

Ignition switch: ON

Indicates the condition of EVAP leak diagnosis.

EVAP DIAG READY

Ignition switch: ON

Indicates the ready condition of EVAP leak diagnosis.

⁽¹⁾	Accelerator pedal position sensor 2 signal and throttle position sensor 2 signal are converted by ECM internally. Thus, they differ from ECM terminals voltage signal.

⁽²⁾	For Flexible Fuel Vehicle

⁽³⁾	Before measuring the terminal voltage, confirm the battery is fully charged. Refer to "HOW TO HANDLE BATTERY ".