Inspection Procedure
WARNING: This page is about a different car, the 2004 Toyota Camry Solara. However, it is still accessible from the selected car via links, so may be relevant.
- INSPECT STEERING PAD SWITCH ASSY
- Disconnect the radio receiver assy R2 or R6 connector.
- Measure the resistance according to the values in the table below.
Standard:
SPECIFIED CONDITIONTester connection Condition Specified condition SW1 (R6-7) - GND (R6-6) (1) No switch is pushed Approx. 100 kΩ SW1 (R6-7) - GND (R6-6) (1) SEEK+ switch: pushed Approx. 0 Ω SW1 (R6-7) - GND (R6-6) (1) SEEK- switch: pushed Approx. 0.3 kΩ SW1 (R6-7) - GND (R6-6) (1) VOL+ switch: pushed Approx. 1 kΩ SW1 (R6-7) - GND (R6-6) (1) VOL- switch: pushed Approx. 3.2 kΩ SW2 (R6-8) - GND (R6-6) (1) No switch is pushed Approx. 100 kΩ SW2 (R6-8) - GND (R6-6) (1) MODE switch: pushed Approx. 0 Ω SW1 (R2-7) - GND (R2-6) (2) No switch is pushed Approx. 100 kΩ SW1 (R2-7) - GND (R2-6) (2) SEEK+ switch: pushed Approx. 0 Ω SW1 (R2-7) - GND (R2-6) (2) SEEK- switch: pushed Approx. 0.3 kΩ SW1 (R2-7) - GND (R2-6) (2) VOL+ switch: pushed Approx. 1 kΩ SW1 (R2-7) - GND (R2-6) (2) VOL- switch: pushed Approx. 3.2 kΩ SW2 (R2-8) - GND (R2-6) (2) No switch is pushed Approx. 100 kΩ SW2 (R2-8) - GND (R2-6) (2) MODE switch: pushed Approx. 0 Ω (1) Separate Type Amplifier (2) Built-in Type Amplifier
- NG : Go to step 2
- OK : PROCEED TO NEXT CIRCUIT INSPECTION SHOWN ON PROBLEM SYMPTOMS TABLE (SEE PROBLEM SYMPTOMS TABLE )
- INSPECT STEERING PAD SWITCH ASSY
- Disconnect the steering pad switch assy connector.
- Measure the resistance according to the values in SPECIFIED CONDITION
.
Standard:
SPECIFIED CONDITIONTester connection Condition Specified condition AU1 (12) - EAU (10) No switch is pushed Approx. 100 kΩ AU1 (12) - EAU (10) SEEK+ switch: pushed Approx. 0 Ω AU1 (12) - EAU (10) SEEK- switch: pushed Approx. 0.3 kΩ AU1 (12) - EAU (10) VOL+ switch: pushed Approx. 1 kΩ AU1 (12) - EAU (10) VOL- switch: pushed Approx. 3.2 kΩ AU2 (11) - EAU (10) No switch is pushed Approx. 100 kΩ AU2 (11) - EAU (10) MODE switch: pushed Approx. 0 Ω
- NG : REPLACE STEERING PAD SWITCH ASSY (SEE REPLACEMENT )
- OK : Go to Next Step.
- INSPECT SPIRAL CABLE SUB-ASSY
- Disconnect the connectors from the spiral cable sub-assy.
- Measure the resistance according to the values in the table below.
Standard:
SPECIFIED CONDITIONTester connection Specified condition EAU (C10-10) - EAU (10) Below 1 Ω AU1 (C10-12) - AU1 (12) Below 1 Ω AU2 (C10-11) - AU2 (11) Below 1 Ω
- NG: REPLACE SPIRAL CABLE SUB-ASSY (SEE SPIRAL CABLE )
- OK: Go to Next Step.
- CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSY - RADIO RECEIVER ASSY)
- Disconnect the spiral cable sub-assy connector.
- Measure the resistance according to the values in SPECIFIED CONDITION
.
Standard:
SPECIFIED CONDITIONTester connection Specified condition SW1 (R6-7) - AU1 (12) (1) Below 1 Ω SW2 (R6-8) - AU2 (11) (1) Below 1 Ω GND (R6-6) - EAU (10) (1) Below 1 Ω SW1 (R6-7) - Body ground (1) 10 kΩ or higher SW2 (R6-8) - Body ground (1) 10 kΩ or higher GND (R6-6) - Body ground (1) 10 kΩ or higher SW1 (R2-7) - AU1 (12) (2) Below 1 Ω SW2 (R2-8) - AU2 (11) (2) Below 1 Ω GND (R2-6) - EAU (10) (2) Below 1 Ω SW1 (R2-7) - Body ground (2) 10 kΩ or higher SW2 (R2-8) - Body ground (2) 10 kΩ or higher GND (R2-6) - Body ground (2) 10 kΩ or higher (1) : Separate Type Amplifier (2) : Built-in Type Amplifier
- NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
- OK: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN ON PROBLEM SYMPTOMS TABLE (SEE PROBLEM SYMPTOMS TABLE )