CAMRY SOLARA: Specifications
WARNING: This page does not describe the selected car, but rather 16 other vehicles, including the 2002 Toyota Tundra, 2002 Toyota Tacoma, 2002 Toyota Sienna, 2002 Toyota Sequoia, and 2002 Toyota RAV4. However, it is still accessible from the selected car via links, so may be relevant.
Wheel Alignment Specifications (Camry Solara)
| Cold tire inflation pressure | P205/65R15 92H (Front, rear) | ||||||
| Coupe | 200 kPa (2.0 kgf/cm2 , 29 psi) | ||||||
| Convertible | 220 kPa (2.2 kgf/cm2 , 32 psi) | ||||||
| P205/60R16 91H (Front, rear) | |||||||
| Coupe | 220 kPa (2.2 kgf/cm2 , 32 psi) | ||||||
| Convertible | 230 kPa (2.3 kgf/cm2 , 33 psi) | ||||||
| Front Wheel alignment | Vehicle height | ||||||
| Tire size: 205/65R15 | Front(1) | 220 mm (8.66 in.) | |||||
| Rear(2) | 268 mm (10.55 in.) | ||||||
| Tire size: 205/60R16 | Front(1) | 221 mm (8.70 in.) | |||||
| Rear(2) | 269 mm (10.59 in.) | ||||||
| Camber | -0°31' ± 45' (-0.52° ± 0.75°) | ||||||
| Right-left-error | 45' (0.75°) or less | ||||||
| Caster | 2°08' ± 45'(2.13° ± 0.75°) | ||||||
| Right-lefterror | 45' (0.75°) or less | ||||||
| Steering axis inclination | 12°54' ± 45' (12.90° ± 0.75°) | ||||||
| Right-lefterror | 45' (0.75°) or less | ||||||
| Toe-in (total) | 0° ± 12' (0° ± 0.2°, 0 ± 2 mm, 0 ± 0.08 in.) | ||||||
| Rack end length difference | 1.5 mm (0.059 in.) or less | ||||||
| Wheel angle | |||||||
| Inside wheel | 34°19' ± 1° (34.32° ± 1°) | ||||||
| Outside wheel: Reference | 30° 22' (30.37°) | ||||||
| Rear wheel alignment | Camber | -0°39' ± 45' (-0.65° ± 0.75°) | |||||
| Right-lefterror | 45' (0.75°) or less | ||||||
| Toe-in (total) | 0°24' ± 12' (0.4° ± 0.2°, 4 ± 2 mm, 0.16 ± 0.08 in.) | ||||||
| No. 2 lower suspension arm length difference | 1 mm (0.04 in.) or less | ||||||
| Front axle | Axle bearing backlash | Maximum | 0.05 mm (0.0020 in.) | ||||
| Front axle | Axle hub deviation | Maximum | 0.05 mm (0.0020 in.) | ||||
| Front drive shaft | RH drive shaft Tip of the inboard joint shaft to the dust cover falls |
||||||
| Distance | 2AZ-FE | 90 - 91 mm (3.543 - 3.583 in.) | |||||
| 1MZ-FE | 100.5 mm (3.957 in.) | ||||||
| Drive shaft standard length | |||||||
| 2AZ-FE | LH | 696.6 ± 2.0 mm (27.425 ± 0.079 in.) | |||||
| RH | 972.4 ± 2.0 mm (38.283 ± 0.079 in.) | ||||||
| 1MZ-FE (M/T) | LH | 601.5 ± 2.0 mm (23.681 ± 0.079 in.) | |||||
| RH | 871.6 ± 2.0 mm (34.315 ± 0.079 in.) | ||||||
| 1MZ-FE (A/T) | LH | 586.0 ± 2.0 mm (23.071 ± 0.079 in.) | |||||
| RH | 881.6 ± 2.0 mm (34.709 ± 0.079 in.) | ||||||
| Boot clamp clearance | A | 1.9 mm (0.075 in.) or less | |||||
| B | 1.5 - 2.5 mm (0.059 - 0.098 in.) | ||||||
| C | 3.0 - 4.0 mm (0.118 - 0.157 in.) | ||||||
| Damper clamp clearance | 0.5 - 1.2 mm (0.020 - 0.047 in.) | ||||||
| Front suspension | Lower ball joint turning torque | 1.0 - 3.4 N.m (10-35 kgf.cm, 8.7-30 in..lbf) | |||||
| Stabilizer bar link ball joint turning torque | 0.05 - 1.0 N.m (0.5 -10 kgf.cm, 0.4 - 8.7 in..lbf) | ||||||
Measure the distance from the ground to the center of the front side lower suspension arm mounting bolt.
Measure the distance from the ground to the center of the front side strut rod mounting bolt. |
|||||||